VESPA GTS Super 125 i.e. Service Station Manual Download

Page: 94 / 285

Dashboard

= Digital clock

= Odometer

= Speedometer

= Injection warning light

= Engine oil pressure warning light

= Turn indicators

= High-beam warning light

= Headlight warning light

= Fuel gauge

= Low fuel warning light

= Coolant temperature gauge

= Immobilizer LED

Sealed battery

If the vehicle is provided with a sealed battery, the only maintenance required is the check of its charge

and recharging, if necessary.

These operations should be carried out before delivering the vehicle, and on a six-month basis while

the vehicle is stored in open circuit.

Besides upon pre-delivery it is therefore necessary to check the battery charge and recharge it, if re-

quired, before storing the vehicle and afterwards every six months.

INSTRUCTIONS FOR THE BATTERY REFRESH AFTER OPEN-CIRCUIT STORAGE

1) Voltage check

Before installing the battery on the vehicle, check the open circuit voltage with a standard tester.

- If voltage exceeds 12.60 V, the battery can be installed without any renewal recharge.

- If voltage is below 12.60 V, a renewal recharge is required as explained in 2).

2) Constant voltage battery charge mode

- Constant voltage charge equal to 14.40 to 14.70V

- Initial charge voltage equal to 0.3 to 0.5 for Nominal capacity

- Charge time:

10 to 12 h recommended

Minimum 6 h

Maximum 24 h

3) Constant current battery charge mode

- Charge current equal to 1/10 of the battery rated capacity

- Charge time: Maximum 5 h

Electrical system

Vespa GTS Super 125 i.e.

ELE SYS - 94

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands

VESPA GTS Super 125 i.e., Service Station Manual

Search results

Summary of Contents for GTS Super 125 i.e.

Reviews:

Related manuals for GTS Super 125 i.e.

Brands by name

Popular brands