VESPA GTS Super 125 i.e. Service Station Manual Download | Manualshive

Page: 95 / 285

background image

Battery installation

VRLA battery (valve-regulated lead-acid battery) Maintenance Free (MF)

WARNING

BATTERY ELECTROLYTE IS TOXIC AND IT MAY CAUSE SERIOUS BURNS. IT CONTAINS SUL-
PHURIC ACID. AVOID CONTACT WITH YOUR EYES, SKIN AND CLOTHING. IN CASE OF CON-
TACT WITH YOUR EYES OR SKIN, RINSE WITH ABUNDANT WATER FOR ABOUT 15 MINUTES
AND SEEK IMMEDIATE MEDICAL ATTENTION.
IN THE EVENT OF ACCIDENTAL INGESTION OF THE LIQUID, IMMEDIATELY DRINK LARGE
QUANTITIES OF WATER OR MILK. MAGNESIUM MILK, BATTERED EGG OR VEGETABLE OIL.
SEEK IMMEDIATE MEDICAL ATTENTION.
BATTERIES PRODUCE EXPLOSIVE GASES; KEEP CLEAR OF NAKED FLAMES, SPARKS OR
CIGARETTES; VENTILATE THE AREA WHEN RECHARGING INDOORS.
ALWAYS PROTECT YOUR EYES WHEN WORKING CLOSE TO BATTERIES.
KEEP OUT OF THE REACH OF CHILDREN

1) Battery preparation

Position the battery on a flat surface. Remove the

adhesive sheet closing cells and proceed as quick-

ly as possible to run the subsequent activation

phases.

2) Electrolyte preparation.

Remove the container of the electrolyte from the

pack. Remove and preserve cover strips from the

container, in fact, the strip will later be used as a

closing cover.

Note:

Do not pierce the sealing of the container or

the container itself because inside there is sulphu-

ric acid.

3) Procedure for filling the battery with acid.

Position the electrolyte container upside down with

the six areas sealed in line with the six battery filler

holes. Push the container down with enough force

to break the seals. The electrolyte should start to

flow inside the battery.

Note:

Do not tilt the container to prevent the flow

of electrolyte from pausing or stopping.

4) Control the flow of electrolyte

Vespa GTS Super 125 i.e.

Electrical system

ELE SYS - 95

«
...
93
94
95
96
97
...
»

Summary of Contents for GTS Super 125 i.e.






























































































































































































































































































Reviews:

No comments

Related manuals for GTS Super 125 i.e.

Brand: BANWOOD Pages: 52

Brand: Radio Flyer Pages: 4

Brand: APRILIA Pages: 73

Brand: Rebel Pages: 32

Brand: Yedoo Pages: 21

Brand: ESKUTE Pages: 45

Brand: Hudora Pages: 8

Brand: BPM Pages: 43

Brand: Inventist Pages: 6

Brand: Razor Pages: 14

Brand: Yedoo Pages: 96

Brand: yeep.me Pages: 170

Brand: Shoprider Pages: 20

Brand: General Moped Company Pages: 25

Brand: DAELIM Pages: 47

Brand: Ice Bear Pages: 38

Brand: Garelli Pages: 36

Brand: JDbug Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands