VESPA GTV 125 Service Station Manual Download

Page: 154 / 278

TYPE

IDENTIFICATION

RED

BLUE

YELLOW

Type "A"

- RED

Type "B"

- BLUE

Type "C"

- YEL-

LOW

Main half-

bearing

1.970 ÷

1.973

1.9703 ÷

1.976

1.976 ÷

1.979

Bush-

ing cat-

egory

Crank-

case

halves

category

Internal bush-

ing diameter

after fitting

Possible

fitting

29.025 ÷

29.040

Original

29.019 ÷

29.034

Original

and spare

29.028 ÷

29.043

29.022 ÷

29.037

Original

Match the shaft with two category 1 crank webs

with the category 1 crankcase (or cat. 2 with cat.

2) Furthermore a replacement crankcase cannot

be matched with a crankshaft with mixed catego-

ries. The replacement crankshaft has half-shafts

of the same category.

Crankcase

halves

Engine half-

shaft

Bushing

Cat. 1

Cat. 1

Cat. 2

Cat. 2

Cat. 1

Cat. 2

Cat. 2

Cat. 1

N.B.

TO KEEP THIS POSITION OF THE BUSHINGS
ON THE CRANKCASE, FITTING IS FORCED ON
STEEL RINGS INSERTED IN THE CASTING OF
BOTH CRANKCASE HALVES.

Engine

Vespa GTV 125

ENG - 56

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands