VESPA GTV 125 Service Station Manual Download

Page: 78 / 278

- HV coil primary check

Disconnect the control unit connector and check

that the cable between terminal No. 3 and terminal

No. 8 is not interrupted (see figure).

If non-conforming values are measured, check

again the HV coil primary directly on the positive

and negative terminals.

If non-conforming values are measured, repair the

cables or replace the HV coil.

N.B.

THE MULTIMETER MUST BE SELECTED TO
DETECT CONTINUOUS VOLTAGE.

Electric characteristic

Resistance value:

0.4 ÷ 0.5 Ohm

- HV coil secondary check

Disconnect the spark plug cap from the HV cable

and measure the resistance between the HV cable

terminal and the HV coil negative terminal (see

figure).

If non-conforming values are measured, replace

the HV coil. To carry out a more complete diagno-

sis, check the peak voltage with the multimeter

adaptor.

Specific tooling

020409Y

Multimeter adaptor - Peak voltage de-

tection

Electric characteristic

Resistance value:

~ 3000 ± 300 Ohm

- Pick-Up

Disconnect the control unit connector and connect

the positive wire to connector No. 2 and the neg-

ative wire to connector No. 8 (see figure).

Use the start-up system to run the engine and

measure the voltage produced by the Pick-Up.

Replace Pick-Up if non-conforming values are

measured.

Electrical system

Vespa GTV 125

ELE SYS - 14

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands