VESPA GTV 125 Service Station Manual Download

Page: 79 / 278

N.B.

THE MULTIMETER MUST BE SELECTED TO
DETECT CONTINUOUS VOLTAGE.

Electric characteristic

Resistance value:

> 2 Volt

- HV coil

With the control unit and HV coil connected, meas-

ure the voltage of the coil primary during the start-

up test with the voltage peak adaptor and con-

necting the positive terminal to the ground one and

the negative to the coil positive connector.

If non-conforming values are measured, replace

the control unit.

N.B.

THE PLASTIC CAP OF THE POSITIVE TERMI-
NAL ON THE HV COIL PRIMARY IS BLACK
AND THE NEGATIVE TERMINAL ONE IS
GREEN.

Electric characteristic

Resistance value:

> 100 Volt

Battery recharge circuit

The recharge system is provided with a three phase alternator with permanent flywheel.

The alternator is directly connected to the voltage regulator.

In turn, the latter is directly connected to earth and to the battery positive passing through the 15A safety

fuse.

This system therefore requires no connection to the key switch.

The three- phase generator provides good recharge power and at low revs a good compromise is

achieved between generated power and idle stability.

For this reason, it is very important that the idle speed is adjusted as prescribed.

Specific tooling

020333Y

Single battery charger

020334Y

Multiple battery charger

Vespa GTV 125

Electrical system

ELE SYS - 15

Summary of Contents for GTV 125























































































































































































































































































Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands

VESPA GTV 125, Service Station Manual

Search results

Summary of Contents for GTV 125

Reviews:

Related manuals for GTV 125

Brands by name

Popular brands