VESPA LX Series User Manual Download | Manualshive

Page: 78 / 272

background image

HIGH-BEAM /LOW-BEAM LIGHTS LINE

1) Check that bulbs operate properly.

2) Check fuses No. 1 and 4.

3) Check key switch contacts.

4) Check if there is voltage between the Grey cable (30) of the headlight remote control and the ground

connection. If there is not, check cable harnesses.

5) With the key switch set to «

ON

» and the engine running, check if there is voltage between the Grey

cable (87) of the headlight remote control and the ground connection. If there is not, check cable har-

nesses.

6) Check that the White-Black cable connecting the headlight remote control switch and the control unit

(pin 19) is not interrupted.

7) Check the headlight remote control switch.

8) Check that the continuity between the Grey cable of the light switch and the headlight remote control

is not interrupted.

9) Check the light switch contacts.

10) Check that the cable harnesses of the bulbs and their ground connection are not interrupted.

Fuses

The electrical system is equipped with:

1. four protection fuses «

A

» that can be reached

by removing the shield front cover.

2. two fuses «

B

», located in the battery compart-

ment.

The chart shows the position and specifications of

the fuses in the vehicle.

CAUTION

BEFORE REPLACING A BLOWN FUSE, FIND AND SOLVE
THE FAILURE THAT CAUSED IT TO BLOW. NEVER TRY
TO REPLACE THE FUSE WITH ANY OTHER MATERIAL
(E.G., A PIECE OF ELECTRIC WIRE).

CAUTION

MODIFICATIONS OR REPAIRS TO THE ELECTRICAL SYS-
TEM, PERFORMED INCORRECTLY OR WITHOUT STRICT
ATTENTION TO THE TECHNICAL SPECIFICATIONS OF
THE SYSTEM CAN CAUSE MALFUNCTIONING AND RISK
OF FIRE.

Electrical system

Vespa LX 125 - 150 i.e.

ELE SYS - 78

«
...
76
77
78
79
80
...
»

Summary of Contents for LX Series

















































































































































































































































































Reviews:

No comments

Related manuals for LX Series

Brand: W-Tec Pages: 19

Brand: PMG Pages: 9

Brand: Coccolle Pages: 12

Brand: Wottan motor Pages: 85

Brand: Jetson Pages: 22

Brand: Eton America Pages: 65

Brand: WISPEED Pages: 57

Brand: IconBiT Pages: 12

Brand: Malaguti Pages: 32

Brand: Malaguti Pages: 62

Brand: Malaguti Pages: 134

Brand: Baotian Pages: 100

Brand: Roma Medical Pages: 20

Brand: Robstep Pages: 71

Brand: ForU Pages: 80

Brand: Benelli Pages: 178

Brand: RAM WHEELS Pages: 19

Brand: Vermeiren Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands