TECHNICAL SPECIFICATIONS
- Rated voltage
3.6 V DC
- Capacity
800 mAh
No-load speed
280 min
-1
Torque
- Electric power (Max.)
2 N
･
m
- Hand operation (Max.)
10 N
･
m
Weight (not including accessories) 160 g
Permitted ambient temperature
- during charging
0
ﾟ
C - 40
ﾟ
C
- operating* and storaging
0
ﾟ
C - 45
ﾟ
C
Battery Li-Ion
Number of battery cells
1
Charging time
Approx. 60 min
Number of charges**
Approx. 500 charges
Charging port
micro USBType-B
Noise
66.1 dB
according to EN 62841-1 Annex I
Vibration values
0.421 m/s
2
according to EN 62841-1 Annex I, EN 62841-2
Input power (maximum) - Volt
5 V
-Current
1 A
* limited performance at temperatures <0 °C
**Actual battery life will vary depending on specifications.
- Specifications and sizes are subject to change without notice.
CHARGING
Use a charger with the specified charging
capacity.
(Output: 5 V-1 Amp)
If the current value is high, the life of the internal
battery will be shortened.
* This product does not come with a charger.
1) Open the protective cap
(see the figure on the
right) of the power tool
charging port and insert
the USB charging cable.
Charging may not be possible if
the USB charging cable is not
correctly inserted into the charging port.
- Open after pulling out the cap.
- Use the USB charging cable included with this product.
- Opening from the reverse direction will cause a damage.
2) Insert the other end of the USB charging
cable to a USB port designated in the specifi-
cations (commercially available AC adapters,
PCs, mobile batteries, etc.).
The charging lamp
lights up and the charging starts. While charging the
battery, the charging lamp lights red. When charging
is complete, the charging lamp lights green.
Note:
The battery supplied is partially charged. To
ensure full capacity of the battery, completely
charge the battery in the battery charger before
using the product for the first time. The lithium-ion
battery can be charged at any time without reducing
its service life. Interrupting the charging procedure
does not damage the battery. The Lithium-Ion
battery is protected against deep discharging.
Note:
If the charge level of the battery is less than
15%, the battery charge lamp will flash red during
operation. When the battery voltage drops to the
specified value, it cannot operate to protect the
product. Stop work and charge the battery.
Note:
The product cannot be used during charging.
The screwdriver will not operate if the switch is
sliding during charging - this is not a breakdown.
Note:
If not used for a long time, disconnect the
charger from main power.
3) When charging is complete, remove
the USB
charging cable and close the protective cap. Dirt
and foreign matter may cause malfunction.
CHANGING THE TOOL
Only use the specified bits. If you use bits other than
those specified, bits may not be possible to be removed.
- Bits
that can be used are limited to products with
the following mounting dimensions.
- Inserting bit
: Slide the sleeve forward, insert the bit
all the way in, and release the sleeve. Move the bit
back and forth to make sure it is locked. Risk of
injury if the bit comes off while operating.
- Removing bit
: Slide the sleeve forward, pull out the
bit and release the sleeve. Be careful not to drop
bits or the power tool when operating at height.
CAUTION:
Do not slide the switch when
inserting or removing bits.
The power tool
may operate and cause injury.
LED indication
lights up in
red
while charging.
lights up
green
when complete.
13mm
14mm
Charging port
(MicroUSB-typeB)
Charging port (USB-typeA)
Φ
16
140
Φ
45
SIZE
5
