background image

12 

 

 

Types of fuel 

 

Wood needs to be well seasoned before it is burnt. Different woods 
take varying amounts of time to season but, as a general guide, be-
fore being used in a stove, wood should be cut to length, split and 
then stacked under cover (with the sides open to the air) for at least a 
year. Wood is ready for burning when radial cracks appear in the end 
of the logs and the water content is no higher than 20%. It is then 
good practice to have it in the log basket, inside the house, for a few 
days before it is actually used in the stove. The internal width of the 
firebox is 350mm and so firewood should be no longer than this. 
 
Do not burn unseasoned wood in your wood burner. Do not burn par-
ticle board, lacquered, painted or treated wood, plastics, rubber or 
liquid fuels. The stove is not suitable for burning solid fuel i.e. bri-
quettes\ coal\coke\smokeless fuel. The stove should not be used as an 
incinerator.   
 

Remember

 water doesn't burn so use dry fuel. Wet wood causes 

black glass and tar build up inside chimneys and will damage your 
appliance. 
 

Ashes

 

The ashes should only be removed when the fire is out and has been 
left to cool completely. The wood bar can be removed to make access 
easier 

(figure 3)

.  Wood burns well in it’s own ash and so a thin layer 

of ash can be left in the bottom of the stove, this also helps to protect 
the base fire bricks. 

 

Note: The above notes on operating your stove should be taken as 
guidelines only. Each stove installation is unique and the operation of 
each stove is subject to many variables including; the fuel used, the 
size of the room, chimney performance, ventilation. As such, the best 
operation of your stove will be learned through experience only. 
 

 

Summary of Contents for 4



























Reviews: