background image

 

General Safety Advice 

 
 
Properly installed, operated and maintained, this appliance will not 
emit fumes into the dwelling. However occasional fumes from de-
ashing and re-fuelling may occur. Persistent fume emission is poten-
tially dangerous and must not be tolerated. If fume emission does 
persist, open doors and windows to ventilate the room. Let the fire 
burn out or eject and safely dispose of fuel from the appliance. Once 
the fire is cold, check 
the flue and chimney for blockages and clean if required. Do not at-
tempt to relight the fire until the cause of the fume emission has been 
identified and corrected. Seek expert advice if necessary.  
 
· Do not fit an extractor fan in the same room as the appliance. 
· An adequate air supply for combustion and ventilation is essential 
in accordance with Building Regulations 
Document J Section 2. Air openings provided for this purpose must 
not be restricted. 
· It is important that flue ways are cleaned frequently and the chim-
ney swept regularly. Also the stove must be 
maintained in good mechanical order. The chimney should be swept 
at least once per year for smokeless fuel 
and a minimum of twice per year for other fuels. 
· If the chimney was previously used for an open fire, it is possible 
that the higher flue gas temperatures generated by the stove may 
loosen deposits that were firmly adhering to the inner surface of the 
chimney and cause blockage of the flue pipe. We recommend that in 
such a situation a second sweeping of the chimney should be carried 
out within one month of regular use of the stove after installation. 
Also, lock open or remove any existing dampers in the flue way. 
· Should it be likely that children, aged or infirm people approach the 
fire, then a fireguard should be fitted. 
· Avoid the use of aerosol sprays in the vicinity of the stove when it 
is in operation. 
 

Summary of Contents for 4



























Reviews: