background image

 

2021.A 

 

 

5.3 

  Operations

 

 

Turn the oven ON and select a cooking temperature. Two additional controls are used to control the 

fan (as described below). 

The timer is a reminder to you of when to remove food from the oven. The timer does not control the 

temperature of the oven. 

To cook, do the following: 

1.  Turn the oven ON using the Power Switch at the top of the control panel. 

2.  Select the desired fan speed using the Fan Speed switch. The appropriate fan speed (HI or LOW) 

depends on the type of food being cooked. 

3.  Switch the Fan Mode switch to COOK. The fan will run continuously when the oven doors are 

closed (the fan does not cycle on and off with the burners). (If this switch is set to COOL, the only 

difference is that the fan will continue to run when the oven doors are open.) 

4.  Set the cooking temperature by turning the Cook Temperature Control until the indicator mark on 

the knob is pointed to desired cooking temperature. The HEAT ON indicator will light when the 

burners are on and will remain on while the oven preheats. 

5.  Wait until the HEAT ON indicator has come on and gone out three times. At that time the oven will 

have reached the set cooking temperature. 

6.  Open the oven doors, load the product into the oven, and close the doors. 

7.  You  can  use  the  Cook  Timer  as  a  reminder  of  when  to  remove  the  load  from  the  oven.  If  so 

desired, turn the Cook Timer knob until the indicator mark points to the desired cooking time (up 

to  55  minutes).  The  timer  knob  will  rotate  counterclockwise  as  the  timer  runs  down,  indicating 

how  much  time  remains.  You  can  turn  the  knob  while  cooking  to  increase  or  decrease  the 

remaining time. When the timer runs out, a buzzer will sound for a short time, then turn itself off. 

(To immediately silence the buzzer, turn the Cook Timer knob to the OFF position.) The timer is a 

reminder to you; the timer does not control the oven. 

If you open the oven doors, the burners and fan will shut off until the doors are closed. However, 

the timer will continue running even if the doors are open. 

For ovens that are equipped with an oven interior light, to turn on the light, press and hold  the 

switch located at the bottom of the control panel.

 

 

       

 

FGC timer instructions: 

1.

 

  If the set time is 

 5 minutes, rotate it clockwise to the required set time; 

2.

 

  If the set time is 

5 minutes, rotate it clockwise to the position indicating 5 minutes or a little 

more than 5 minutes, and then rotate it counterclockwise to the required set time.

 

 

 

8.  Cool down the oven: 

Step 1: Turn the thermostat to minimum. 

Step 2:

 

Open the door then switch to COOL mode ,the fan will run to cool down the oven . 

For the most rapidly cooling ,switch the Fan Speed to HI. 

Summary of Contents for FGC100















Reviews: