Subject to modifications.
© Vestamatic GmbH
Art.-Nr.: 85700621 H1 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
VRS WISO Crystal Control
1/4
G
VRS WISO
Crystal Control
Art.-no.:
01180002
Installation and Operating Instructions
VRS WISO Crystal Control
Art.-no.: 01180002
Radio controlled weather station with integrated wind/lux sensor
and incl. mounting bracket.
Short description
Radio controlled weather station with integrated wind / lux sensor
Compatible with all Vestamatic motors of VRS-Line VL-ME-WISO-35/45
The weather station is ready mounted on a mounting bracket.
Safety precautions
– Contact a professional electrician to install the control sys-
tem, because the control system requires a power supply of
230VAC, 50 Hz.
– Check the control system for signs of mechanical damage
after unpacking. If you notice any shipping damage, do not start
up the control system and notify your supplier immediately.
– The control system should only be used for the purpose spec-
ified by the manufacturer (refer to the operating instructions).
Any changes or modifications thereof are not permissible and
will result in loss of all warranty claims.
– If the control unit or the connected sunshade cannot be oper-
ated without presenting a hazard, it must be switched off and
prevented from being switched on unintentionally.
– When performing work on the windows, controls or connected
shades, protect them against unauthorised or unintentional
operation.
Scope of delivery
1 × VRS WISO Crystal Control
1 × power supply 230VAC / 12VDC, 1 A
1 × surface-mount housing for power supply
1 × magnet
6 × dowel including screws
6 × chandelier terminals
Technical data
Power supply:
12 VDC, 25 mA, 0.3 W
Impulse voltage withstand level: 2.5 kV
Radio frequency:
868 MHz
Wind speed sensor:
Measuring range:
3 ... 17 m/s
Lux sensor:
Measuring range:
0 ... 40 kLux
Range:
max. 30 m
Operating temperature:
-15 °C (+5 °F) to +60 °C (140 °F)
Connectable VRS motors:
max. 10 (VL-ME-WISO-35/45)
Protection degree:
IP 44
Material (plastic parts):
UV-stabilised polycarbonate
Conformity:
p
Conformity
This product conforms to the basic requirements of the R&TTE Directive
1999/5/EC. The declaration of conformity can be found on the web page:
www.vestamatic.com
Assembly and installation
The sensor unit must be installed and connected by a professional elec-
trician.
1. When deciding where to install the sensor unit, ensure that the wind
speed and sun intensity readings, taken at the mounting location, are
similar to those, taken on the shading device.
WARNING!
Do not mount the sensor unit in the shade, or shelter, of the
extended shading device. The wall mount should be at-
tached with the sensor unit column pointing upwards as
shown in figure 1.
2. Attach the wall mount using the supplied installation kit.
3. Connect the power supply cable to the sensor cable according to the
wiring diagram.
4. If necessary, adjust the sensor unit (a) so, that together with the lux
sensor (b), it captures maximum sun intensity.
Figure 1
WARNING!
Risk of injury due to improper installation and commissioning.
Improper installation and commissioning may lead to per-
sonal injury or property damage.
Therefore:
– When connecting the device, observe the currently valid
VDE standards (in particular DIN VDE 0100/0700), your local
power company’s regulations and the current accident pre-
vention regula tions.
– Connect the control in accordance with the wiring diagram.
Wiring diagram
G
85700621 H1
