Subject to modifications.
© Vestamatic GmbH
Art.-Nr.: 85700621 H1 • Vestamatic GmbH • Dohrweg 27 • D-41066 Mönchengladbach • www.vestamatic.com
VRS WISO Crystal Control
3/4
G
Function and programming VRS WISO Transmitter 5
Programming a VRS WISO Transmitter 5
for initial operation respectively after RESET
Now press the prog.-button (Fig. A) on the backside
of the transmitter, followed by the STOP button.
Successful programming:
The motor will confirm this with two short movements
in both directions.
Fig. A
Select the required switching channel on your transmitter. Change chan-
nel as described above by pressing the STOP button.
Switch OFF the power supply of the motor for minimum 3 seconds.
Switch ON the power supply again, the motor is now in programming
mode for 30 seconds.
Ergonomics to “add / pair”
c motor
With VRS WISO Transmitter 5:
You need a VRS WISO Transmitter 5 to
add
the control to a motor. This trans-
mitter must be known / authorized by the
system.
With this transmitter you put the motor
into “learn” mode. When motor is in
“learn” mode, hold magnet close to
PROG POINT at the sensor, and it will
control your motor.
Please proceed in the following way:
– Press and release prog.-button once on the backside of VRS WISO
Transmitter 5 (LED 1 blink).
– Press STOP button, and motor will move UP / DOWN and enter “learn”
mode.
– Hold magnet close to PROG POINT at the sensor. If sensor is con-
nected to the motor, the motor will confirm this with a short movement
in both directions.
Control is now paired with the motor and will control the motor.
Without VRS WISO Transmitter 5:
If a VRS WISO Transmitter 5 is not available, the motor can be turned
OFF / ON to enter “learn” mode for 60 seconds. This will also allow the user to
add the sensor to the motor by holding magnet close to PROG POINT at the
sensor. The motor will confirm this with a short movement in both directions.
Ergonomics to “remove / unpair”
c motor
You need a VRS WISO Trans-
mitter 5 to
remove
the control
from a motor. This transmitter
must be known / authorized by
the system.
With this transmitter you put
the motor into “forget” mode.
When motor is in “forget”
mode, hold magnet close to
PROG POINT at the sensor,
and it will be removed from
your system.
Please proceed in the following way:
– Press prog.-button on the backside of VRS WISO Transmitter 5 until
LED 1, 2, 3 is lit.
– Press STOP button.
– Hold magnet close to PROG POINT at the sensor (within 10 seconds).
If sensor is removed from the motor, the motor will confirm this with a
short movement in both directions.
Control is now unpaired from the motor, and will not control the motor any-
more.
Note:
If you switch off the power of the VRS WISO Crystal Control, the
motor will be locked by the security time-out after some minutes.
Therefore it’s important to unpair the devices if you want to re-
move the sensor permanently.
A.
LED indication of selected channel of the
transmitter. In total there are five channels on
the transmitter.
B.
VRS WISO Transmitter 5:
Used to select and display manual or
automatic mode.
C.
Manual control buttons.
Channel 1– 5 = Motor / Shade
Button ON/UP =
Q
Button STOP
Button OFF/DOWN =
q
To change manual / automatic mode:
Press and hold STOP button for 7 s, then use
ON/UP
Q
or OFF/DOWN
q
button to select
manual or automatic mode. Confirm mode by
pressing STOP button.
Manual mode:
Motor is controlled only by
wind functionality.
Automatic mode:
Motor is controlled by
sun and wind functionality.
To change channel:
Press and hold STOP button for 3–6 s (LED
start to blink), then use the ON/UP
Q
or OFF/
DOWN
q
button to select wanted channel and
confirm by pressing STOP button.
A.
B.
C.
