background image

Table of Contents

 

Rev. 4/22/2019 

   FMDL MANUAL 

 

Table of Contents

 

Copyright 2019   Vestil Manufacturing Corp.  

 

Page 2 of 16 

Specifications:

 

Dimensions and other product specifications appear in the table.

 

 

 

 

Signal Words:

 

 

This manual classifies personal injury risks and situations that might cause property damage with signal words. 

Signal words indicate the seriousness of injuries that might result if a particular act does, or does not, occur. 

   

 

 

  Identifies a hazardous situation which, if not avoided, WILL result in DEATH or SERIOUS 

INJURY.  Use of this signal word is limited to the most extreme situations. 

 

   

 

  Identifies a hazardous situation which, if not avoided, COULD result in DEATH or SERIOUS 

INJURY. 

 

 

  Identifies practices likely to result in product/property damage, such as operation  that might 

damage the drum lifter.

 

 

 

Hazards:  

  We strive to identify all hazards associated with the use of our products. However, material handling is 

dangerous and no manual can address every risk. The most effective way to avoid injury is for the end-user to 

exercise sound judgment whenever using this product. 

 

 Improper or careless use of this product might result in serious personal injury.   

  DO NOT exceed the maximum rated load of your lifter (see Label on product; also see table on p. 2). 

  DO NOT use an unsound drum lifter.  If any of the following conditions are present, do not use the lifter:  1) 

missing,  broken or significantly bent drum-gripping mechanism; 2) broken, missing, or deformed safety  chain; 3) 

severely damaged/worn fork pockets. Inspect the drum lifter according to the 

Inspections

 on p. 

12

. Replace each 

part that fails to pass an inspection. DO NOT use the drum lifter until it is in 

Original Condition

. 

  No part of your body should ever be beneath any part of the lifter or drum while it is elevated.  

  DO NOT use the lifter to transport 

anything

 but drums matched to your lifter. Se

Specifications

 (above). 

  Transport drums slowly. Avoid rough terrain when transporting drums. Jostling might disrupt the grasp on the rim. 

DO NOT transport drums over rough terrain UNLESS they are secured to the lifter with a ratchet strap. 

  DO NOT modify the drum lifter in any way without  first obtaining  written approval from Vestil.  Unapproved 

modifications automatically void the 

Limited Warranty

 (p. 16) and could make the lifter unsafe to use. 

  DO NOT use the lifter UNLESS all labels are easily readable and undamaged. See 

Labeling Diagram

, p. 12. 

  For the Eagle Beak™ mechanism to work properly, the drum plus contents must weigh at least 50lb. (~22.7kg). 

  The chain is an essential safety-enhancing feature. Wrap the chain around the fork carriage and fasten the free 

end to the chain or quick link 

with no slack

.

 

 

 

 

Model 

Description 

Compatible Drums  

 

Capacity

 

 

Overall 

Dimensions 

Net 

Weight  

FMDL-1 

Eagle Beak™ 

single drum 

carrier 

  30 & 55 gallon 

  Open & closed head 

  Steel, plastic, & fiber 

1,000 lb. 

(~455kg) 

26½” x 46½” x 29” 

(67 x 118 x 74)cm  

240 lb. 

(~109kg) 

FMDL-2 

Eagle Beak™ 

two drum carrier 

  30 & 55 gallon 

  Open & closed head 

  Steel, plastic, & fiber 

2,000 lb. 

(~909kg) 

42” x 49½” x 29” 

(107 x 126 x 74)cm 

340 lb. 

(~155kg) 

DFDL-3 

Deluxe 3-mode 

drum lifter: 

Eagle beak, 

Bottom grip & 

Top grip 

  30 & 55 gallon 

  Open & closed head 

  Steel, plastic, & fiber 

 

Eagle Beak™ = 

     1,000 lb. (~455kg) 

Bottom grip = 

     800 lb. (~364kg) 

Top grip = 

     1,100 lb. (~455kg)

 

 

26½” x 52” x 30” 

(67 x 132 x 76)cm 

313 lb. 

(~142kg) 

FPDL-8-L 

(“L” = low 

attachment

Bottom gripping 

drum handler for 

oddly shaped 

plastic drums 

  55 gallon 

  Open & closed head 

  Plastic 

800 lb. 

(~364kg) 

26½” x 56½” x 23” 

(67 x 144 x 58)cm 

160 lb. 

(~73kg) 

FPDL-11-H 

(

“H” = high 

attachment

Top gripping 

drum handler for 

oddly shaped 

plastic drums 

  30 & 55 gallon 

  Closed head 

  Steel, plastic, & fiber 

1100 lb. 

(~500kg) 

26½” x 48½” x 23” 

(67 x 123 x 58)cm  

185 lb. 

(~84kg) 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for DFDL-3

















Reviews: