background image

Table of Contents

 

Rev. 3.19.2020 

LAD-TRN MANUAL 

 

Table of Contents

 

Copyright 2020 Vestil Manufacturing Co. 

Page 8 of 12 

 

ASSEMBLY INSTRUCTIONS 

  Improper or incomplete assembly might result in a ladder that is unsafe to use. 

  Visually inspect all  ladder  components 

prior to assembly

.  Look at each part of the ladder immediately after you 

receive the package from the shipper.  Determine whether damage occurred during shipping. DO NOT assemble or use 

the  ladder stand  if you notice any  damage, especially to the step weldment, back leg weldment, base supports, or 

handrails.  Using a damaged component could lead to ladder collapse and result in serious personal injuries. 

  While assembling this ladder, confirm that only locking fasteners are provided, i.e.  only locking nuts. Contact 

TECHNICAL SERVICE

 (p. 1) if you find non-locking nuts. Only lock nuts should be used. However, lock nuts can only 

safely be used once. Discard the used lock nut and install a new lock nut after unfastening a connection 

  DO NOT assemble the ladder by yourself.  At least 2 people are needed for assembly. 

  Read the entire instruction manual before assembling this ladder. 

  DO NOT use the ladder if a wheel is damaged. Damaged wheels might cause the ladder to wobble or tip when used. 

The following tools are necessary to assemble the ladder: 2 crescent wrenches (

5

/

16

” and 

3

/

8

”); Rubber mallet. 

 

NOTE:

 Numbers in diagrams and in parentheses () correspond to part numbers in the exploded views on p 4-7. 

 

 

Step 1:  Fasten the back leg tubes (44-014-487) to the back leg weldment with bolts (11062) and lock nuts 

(37021). Then, attach the back leg weldment to the stair frame weldment with 

5

/

16 

in. hardware. Be sure to 

orient the back leg weldment as shown below (support tabs should face inwards). 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

  Step 2: Fasten the base supports to the slotted bolt holes in the support brackets and to the support tabs with 

5

/

16

”–

18 hardware as shown. Do not tighten the connections. 

 

 

 

 

11060

 

       

 

 

Back leg 

weldment 

Stair frame 

weldment 

37021

 

 

 

 

 

 

Ladder 

assembly 

Support 

tab 

Wheel 

bracket 

Support 

bracket 

 

Base 

support 

 

37021 

11055 & 33006 

 

37021 

33006    11055 

11060 

37021 

Back leg tube 

Wa
ll 

Summary of Contents for LAD-TRN Series













Reviews: