background image

 

Rev. 1/19/2017 

 PLDL, MANUAL 

 

Copyright 2017 Vestil Manufacturing Corp. 

 

 

Page 5 of 5 

 

Maintenance: 

At least once per month inspect to unit to ensure that it remains in normal condition for as long as possible.  

  Inspect the wheels. Remove embedded material. Look for damage including severe wear. If a wheel does not roll 

smoothly across the floor due to wear or other damage, replace the wheel.  Do not use the dolly again until approved 
replacement parts have been installed. 

  Inspect fasteners (see FIG’s 1A and 1B on p. 3).  Install replacement parts as required. 

  Examine the axles and wheel bearings for damage.  Remove the dolly from service if either axle is damaged.   

  [PLDL-LD & -HD] Open the dolly and examine the hinge; then turn the dolly over and examine the bottom side of the 

hinge.  If the hinge is pulling apart, remove the dolly from service.  

  [PLDL-ADJ] Examine the adjustment tubes for cracks, severe wear, etc. 

Limited Warranty: 

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship during 
the warranty period. 

Our warranty obligation is to provide

 

a replacement for a defective original part

 

if

 

the part is covered 

by the warranty

after we receive a proper request from the warrantee (you) for warranty service

 

Who may request service? 

Only a warrantee may request service.  

You are a warrantee 

if

 

you purchased the product from Vestil or from an 

authorized distributor AND Vestil has been fully paid. 

 

What is an “original part”? 

An original part is a part 

used to make the product as shipped

 to the warrantee. 

 

What is a “proper request”? 

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the 
shipping date; AND 2) a written request for warranty service including your name and phone number.  Send requests by 
any of the following methods: 

 

 

     Mail   

 

 

 

                  Fax   

 

 

Email 

       Vestil Manufacturing Corporation 

 

           (260) 665-1339   

    sales@vestil.com 

       2999 North Wayne Street, PO Box 507 

                  Phone 

       Angola, IN 46703   

 

 

           (260) 665-7586 

 

Your request must list the parts believed to be defective and include the address where replacements should be 
delivered. 

 

What is covered under the warranty?

 

After Vestil receives your request for warranty service, an authorized representative will contact you to determine 
whether your claim is covered by the warranty.  Before providing warranty service, Vestil may require you to send the 
entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the following 

original

 dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders.  It also covers 

defects in 

original

 parts that wear under normal usage conditions (“wearing parts”), such as bearings, hoses, wheels, 

seals, brushes, and batteries. 

 

How long is the warranty period?

 

The warranty period for original dynamic components is 30 days. For wearing parts, the warranty period is 30 days. The 
warranty periods begin on the date when Vestil ships the product to the warrantee.  If the product was purchased from 
an authorized distributor, the periods begin when the distributor ships the product.  Vestil may, at its sole discretion, 
extend the warranty periods for products shipped from authorized distributors by 

up to

 30 days to account for shipping 

time. 

 

 

If a defective part is covered by the warranty, what will Vestil do to correct the problem?

 

Vestil will provide an appropriate replacement for any 

covered

 part.  An authorized representative of Vestil will contact 

you to discuss your claim. 

 

What is not covered by the warranty? 

 Labor; 

 Freight;  

  Any of the following, which automatically void the warranty: 

1. 

Product 

misuse; 

    5. 

Damage 

sustained 

during 

shipping; 

   

2.  Negligent operation or repair; 

 

 

6. Accidents involving the product; 

3.  Corrosion or use in corrosive conditions;  

7. Inadequate or improper maintenance; 

4. Unauthorized modifications:  DO NOT modify the product IN ANY WAY without first receiving written 

authorization from Vestil.  Modification(s) might make the product unsafe to use or might cause excessive and/or 
abnormal wear. 

 

Do any other warranties apply to the product? 

Vestil Manufacturing Corp.

 

makes no other express warranties. All implied warranties are disclaimed to the extent 

Summary of Contents for PLDL-Series






Reviews: