background image

TABLE OF CONTENTS

 

Rev. 3/7/2022 

VST-4-Y, MANUAL 

 

TABLE OF CONTENTS

 

Copyright 2021 Vestil Manufacturing Corp.                                                      Page 2 of 10 

 

SIGNAL WORDS  

  SIGNAL WORDS appear in this manual to draw the reader’s attention to important safety-related 

messages. The following are signal words used in this manual and their definitions.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SAFETY INSTRUCTIONS 

  Vestil strives to identify hazards associated with the use of its products, but no manual can address 

every conceivable risk. Minimize the likelihood of injury by recognizing the hazards identified below and 

by inspecting and maintaining the product as instructed in 

INSPECTIONS & MAINTNENANCE

 on p. 8.

 

 

 

WARNING 

Hazardous conditions could result in serious personal injuries or death.  

 

Read and understand the entire manual before assembling, using, inspecting, or servicing the steps.

 

 

DO NOT use the steps unless you are in good health. NEVER use the steps while under the influence of 

alcohol or drugs, including prescription medication that affects balance, perception, or judgment.

 

 

DO NOT exceed the capacity/rated load. The total weight applied to the stepstool  (weight of the 

user plus tools, etc.) must not be greater than the capacity indicated on the riser of the top step (500 lb.; 

227kg).

 

 

 

Do not use the unit if the steps are cracked, dented, or damaged in other ways. Do not use the unit 

unless handrails are solidly fastened to the steps.

 

 

Wear appropriate footwear. DO NOT wear high-heeled shoes or footwear with smooth soles.  

 

DO NOT use the steps  on uneven, sloped, or unstable surfaces. 

ONLY use the steps  on even, level, 

improved surfaces (e.g. concrete or asphalt).

 

 

Make sure that you will not contact overhead objects during use.  

 

Avoid electrical shock! Take precautions to prevent contact, or possible contact, with an energized, 

electrical wire/cord. 

 

Remove dirt and debris from your shoes 

before

 walking on the steps. Only wear slip-resistant shoes. 

 

Only stand on the steps. DO NOT climb on the railing. DO NOT slide on the railing. 

 

DO NOT step onto, or off of, any step from another elevated surface. 

 

ALWAYS face the stairs and use the handrails while ascending and descending the stepstool.  

 

DO NOT increase the height of a step by standing on other objects placed on one of the steps. 

 

Inspect the steps as described in 

INSPECTIONS & MAINTENANCE

 on p. 8. DO NOT use the stool unless it 

is in 

SATISFACTORY CONDITION

. ONLY use manufacturer-approved replacement parts when repairs are 

necessary. See 

RECORD OF SATISFACTORY CONDITION

 on p. 8. 

 

DO NOT use the steps  if  1 or more  of the molded  rubber  feet  (14-145-179) is significantly  worn, 

damaged, or missing. See 

EXPLODED VIEW

 on p. 4. Only use the steps if all 4 feet are in place and are in 

SATISFACTORY CONDITION

. 

 

ONLY use the steps as standing surfaces. DO NOT use it for any other purpose. DO NOT store materials 

or equipment on the steps. Always unload the steps before leaving them unattended. 

 

DO NOT use the steps in front of a door unless the door is secured in an open position, is locked, is 

attended, or is barricaded. 

 

DO NOT lean, or reach, over the handrails/sides of the steps. Position the steps as close to the work as 

possible. Reposition the steps to prevent overreaching. Overreaching could cause instability and result 

in a fall. 

 

Avoid sudden shifts while on the steps. 

 

DO NOT skip steps. Climb the steps one step at a time. 

 

DO NOT attempt to move the steps while someone is using them. 

Continues on next page 

     DANGER

 

Identifies a hazardous situation which, if not avoided, WILL  result in DEATH or 

SERIOUS INJURY.  Use of this signal word is limited to the most extreme situations

.

 

 

 

WARNING

 

Identifies a hazardous situation which, if not avoided, COULD result in DEATH or 

SERIOUS INJURY.

 

 

 

CAUTION

 

Indicates a hazardous situation  which, if not avoided, COULD result in MINOR or 

MODERATE injury.

 

 

 

NOTICE

 

Identifies practices likely to result in product/property damage, such as operation 

that might damage the product

 

Summary of Contents for VST-4-Y











Reviews: