background image

TABLE OF CONTENTS

 

Rev. 3/7/2022 

VST-4-Y, MANUAL 

 

TABLE OF CONTENTS

 

Copyright 2021 Vestil Manufacturing Corp.                                                      Page 3 of 10 

WARNING 

Continued from p. 2. 

 

DO NOT use the steps to transport people or objects. DO NOT ride on the steps while it is moved. 

 

DO NOT remove or obscure any label or information molded into the steps. Each label and all molded 

information must be in place, readable, & undamaged. See 

LABELING DIAGRAM

 on p. 9. 

 

DO NOT modify this steps! Modifying the steps automatically voids the 

LIMITED WARRANTY

 

(p. 10)

 

and 

might make the steps unsafe to use. 

 

SPECIFICATIONS

 

  Documents that provide specifications for VST series products are available online to anyone who 

visits Vestil’s website. Specifications include dimensions, net weight, and capacity information. To access 

the appropriate specifications document, navigate to the BOL-R 

webpage 

at   

https://www.vestil.com/product.php?FID=632

. Scroll the page to the entry for the specific model you 

purchased. Click the button in the “PDF” column that looks like a pencil inside a blue-bordered box. A 

PDF file will open. This file is the specifications document. Print a copy of the document and keep it with 

your copy of this manual.

 

If your model is not included on the 

VST webpage

, or if you cannot access 

and/or print the specifications document, contact the 

TECHNICAL SERVICE DEPT

. Contact information 

for the department is provided on the cover page of this manual. The following is an exemplar 

specifications document.  

NOTE:

 1

IN

.

 

=

 

2.54

CM

;

 

2.2

LB

.

 

=

 

1

KG

 

 

 

 

 

 

Summary of Contents for VST-4-Y











Reviews: