Vestil VST-4-Y Manual Download

Page: 6 / 10

TABLE OF CONTENTS

Rev. 3/7/2022

VST-4-Y, MANUAL

TABLE OF CONTENTS

Align handrail tubes with handrail posts as shown below. Install a 3/8”-16 x 1.25” socket

cap screw (23307) through the bolt holes of aligned pipe ends (44-516-016) and wind

them into the lock nuts as shown in the diagrams below.

Handrail tubes with pipe ends

Handrail tubes fastened to posts

Tighten all 4 socket cap screws to 15.7ft

∙lb

with your torque wrench.

Tighten all 8 set screws to 2

3ft∙

lb.

Install the handrail stabilizer bar (14-017-041) with 5/16” hardware

Place the handrail stabilizer against the upper handrail posts. The top edge of the

stabilizer should contact the bottoms of the pipe ends.

Install the

”-18 x 1

” U-bolts (42024) around the handrail posts and through the bolt

holes provided at both ends of the stabilizer bar.

Install a 5/16” lock washer (33620) and a 5/16”-18 hex nut (36304) onto each arm of both

U-bolts. Tighten all 4 hex nuts to 8.8

ft∙lb.

Install 5/16”-18 acorn nuts (37709) onto both legs of both U-bolts. Tighten each acorn nut

to 8.8ft∙lb.

Pipe end

Set screw

Lock nut Set screw

(37024) (25537)

Set screw

(25537)

Socket cap

screw (23307)

Handrail stabilizer bar (14-017-041)

U-bolt Lock Hex Acorn

nut nut nut

Stabilizer

bar

Acorn

nut

Hex nut Lock

nut

U-bolt

Handrail

tube

Summary of Contents for VST-4-Y











Search results

Summary of Contents for VST-4-Y

Reviews:

Related manuals for VST-4-Y

Brands by name

Popular brands

Vestil VST-4-Y, Manual

Search results

Summary of Contents for VST-4-Y

Reviews:

Related manuals for VST-4-Y

Brands by name

Popular brands