background image

Safety shoes

Safety shoes protect the feet against crushing, falling components and slipping on slip-

pery floor surfaces.

Risk of injury from the work environment!
– Observe the operating instructions on wearing personal protective equip-

ment.

Regardless of the required personal protective equipment for the activity in

question, it is possible that additional dangers that are not described in this

manual may arise due to the operation site of the folding fork arms. If suitable

personal protective equipment is not used for these dangers, there is a risk of

serious injuries.

2.8 

Protection of the environment and disposal

Danger to the environment from incorrect handling of environmentally haz-

ardous substances!
– Always observe the instructions given below when handling and disposing of

environmentally hazardous substances.

If environmentally hazardous substances are handled incorrectly, particularly if

such substances are disposed of incorrectly, this could cause significant

damage to the environment.

Always observe the following points:

Packaging materials are valuable raw materials and, as such, they can continue to be

used or be reprocessed for practical purposes in many cases. Incorrect disposal of

packaging materials can give rise to dangers to the environment.

n

Reuse packaging materials if possible.

n

If packaging materials cannot be reused, have the materials remanufactured or dis-

posed of in an environmentally responsible manner.

n

Observe the locally applicable disposal regulations. If necessary, arrange for a spe-

cialist company to take care of the disposal.

Further operational

requirements

L

 WARNING

NOTICE

Packaging materials

 Safety

Protection of the environment and disposal

V1.07/2021

Folding fork armsTypes KGA, KGI, and DuoLoc

18

Summary of Contents for DuoLoc

























































Reviews: