INTRODUCTION
Congratulations on your purchase of this product.
This User Guide suits DA-S36 product. We adopt the lat-
est SONY technical of sensor and driver. The most attrac-
tive characteristics are small and easy hidden, suits the
elevator and corridor. In addition, it owns the characters of
high
definition and stability, strong anti-jamming, rich and
real color. Fixing and
using this model are convenient too.
It is very good for you to apply to your CCTV system.
Please read this instruction manual carefully to en-
sure proper use of the product.
CONNECTING
BRIEF OF PRODUCT
*
Sensor
(
CCD
)
Adopt SONY 1/3
"
CCD Sensor.
*
Auto Gain Control (AGC)
Built-in auto gain control
(AGC)
circuit. The color camera
can get high definition picture in low Lux condition.
*
Scanning Mode
NTSC
or PAL
mode.
*
OSD SETTING
DC12V
Power Supply
Monitor
DA-S36
TROUBLE AND SOLUTION
Link wire rule
：
Power
Video
Note
:
●
Please note the camera’s operating temperature and its using
environment
requirement. Avoid using the camera at too high
or too low temperatures. The operating temperature is
-
30~
+
60℃
. (Recommendatory operating temperature is
-
10~+45℃
.)
●
Never make the camera face the sun or bright object. Other-
wise, it will damage the CCD
.
●
Do not mount the camera near by the radiator
or heater.
1. No Picture after providing power
. May be the power supply voltage abnormity, please check the power
supply voltage and pole
whether exactitude
.
. Please check all the connecting cable and monitors whether be connected
correctly or not
.
2. The picture level direction have flowing interference ripples
. May be caused by the power supply AC ripples, it need filter the wave of the
power supply
.
. Check the monitor and peripheral equipments used.
3. The picture background color changes continuously
. The fluorescent lamp’s electromagnetic field cause color roll. This is proper
phenomenon of the cameras.
. Reduce the fluorescent lamp numbers or increase the distance between the
camera and the fluorescent lamps can improve it.
. Use power supply external sync. camera can solve it.
4. The picture smear too mass
. The power supply’s voltage unstable
.
. Connecting cables not connect correctly or have high impedance.
The symbol is intended to alert the user to the presence of
The symbol is intended to alert the user to the presence of
important operating and maintenance (servicing)
Instructions in the literature accompanying the appliance.
uninsulated ‘dangerous voltage’ within the product’s
enclosure
that may be of sufficient Magnitude to
consti-
a risk of electric shock to persons.
Video
DC12V
CAUTION:
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK
DO NOT REMOVE COVER OR BACK NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING
RISK OF ELECTRIC. DO NOT OPEN
CAUTION:
TO PREVENT ELECTRIC SHOCKS AND RISK OF
FIRE HAZARDS, DO NOT USE OTHER THAN
SPECIFIED POWER SOURCE.
Note
：
●
The power supply
must through safe attestation. Its output voltage,
current, voltage polarity
and operating temperature
must match the
camera’s requirement
.
●
When using the camera in the thunderbolt condition
,
please note to
mount Anti-thunder device or put off the power supply plug and cable
.
●
In order to capture high quality pictures, the power supply’s cable and
video output cable should not be too long.
OSD SET
EXPOSURE
LENS
ELC/DC
HBLC/D-WDR
BLC/HLI/D-WDR
AGC
OFF/LOW/MIDDLE/HIGH
3D DNR
OFF/LOW/MIDDLE/HIGH
SENSE UP
AUTO/OFF/X2/X4/X8/X16/X32/X64/
X128/X256/X512
EXIT
COLOR
WB MODE
ATW/MANUAL/AWC>PUSH/AWC
R-Y-GAIN
0~256
B-Y-GAIN
0~256
EXIT
DAY&NIGHT
D&N MODE
AUTO/COLOR/B&W/EXT
FUNCTION
MIRROR
ON/OFF
SHARPNESS
0~30
LSC
ON(0~30)/OFF
MOTION
MOTION
ON/OFF
AREA SEL
TOP/BOTTOM/LEFT/RIGHT
SENSITI
0~30
DISPLAY
OFF/ICON/TRACE
HOLD TIME
0~15 Unit: sec
ALARM
ON/OFF
EXIT
PRIVACY
MASK1~MASK8
ON/OFF
SETUP
TITLE
OFF/ON: 64charaters
DPC
OFF/MANUAL:WHITE THR 0~255/BLACK
THR 0~255/DPC LEVEL:0~255
OLPF
650/850
MONITOR
CRT/LCD
GAMA
0.45/0.60/1.0/USER
EXIT
SYSTEM
CAMERA ID
0~255
COMMUNI
PROTOCOL:PELCO-D
BAUDRATE:2400/4800/9600 bps
RETURN
LANGUAGE
CHINESE/ENGLISH
EXIT
EXIT
FACTORY SET
SAVE&EXIT
EXIT
MENU
UP
DOWN
RIGHT
LEFT
PRESS
KEY BOARD
