background image

USER MANUAL

QUARTER DUTY ONBOARD AIR SYSTEM

P/N 10002

COMPRESSOR WIRING DIAGRAM

15 Edelman

Irvine, CA 92618

949-585-0011

www.viaircorp.com

87

86

30

85

+

-

Battery

To Keyed

Power Source

12V  40A

Relay

Fuse

Pressure

Switch

Rev.1

WIRE GAUGE GUIDE 12-VOLT:

Amp Draw

Length of wire from battery to compressor

10

15

20

25

30

10

14

12

10

10

10

15

12

10

10

8

8

20

10

10

8

6

6

25

10

8

6

6

6

30

10

8

6

6

4

40

8

6

6

4

4

50

6

6

4

4

2

60

6

4

4

2

2

LIMITED WARRANTY:

VIAIR Corporation warrants this product, when properly installed and under normal conditions of use, to be 

free from defects in workmanship and materials for a period of one year from its original date of purchase. 

To receive warranty service or repair, please contact VIAIR Corporation.  

Returns should be made within one year of the date of purchase, after a Return Goods Authorization 

(RGA) number has been assigned by VIAIR Corporation.  To obtain RGA, fax a copy of your receipt to 

(949) 585-0188. For complete warranty details, please visit: 

www.viaircorp.com/warranty

PLEASE NOTE:

THIS WARRANTY COVERS PRODUCT DEFECTS ONLY; IT DOES NOT COVER INCIDENTAL 

OR CONSEQUENTIAL DAMAGES AS RESULT OF MISUSE OR ABUSE. 

15 EDELMAN • IRVINE, CA 92618

TEL: (949) 585-0011 • FAX: (949) 585-0188

www.viaircorp.com 

Wiring Diagram:

(Figure 3)

Summary of Contents for 10002









Reviews: