background image

TIRE INFLATION & DEFLATION

IMPORTANT

:  Before  attaching  air  compressor 

power cord to power source, check to make sure that 
the  ON\/OFF switch of your  compressor is  in the Off 
position.  Attach  the  Positive  (+)  battery  clamp  (Red) 
to  the  Positive  terminal  of  the  battery  and  the 
Negative  (-)  battery  clamp  (Black)  to  the  Negative 
terminal  of  the  battery.    Always  keep  your  vehicle 
engine  running while operating compressor to avoid 
draining your vehicle’s battery. 

CAUTION

:   

Your  Portable  Air  Compressor  is 

Moisture  and  Dust  Resistant,  but  NOT  WATER  OR 
DUST PROOF.  Never place compressor in soft sand 
while  running  the  compressor.    Vibration  from  the 
compressor will cause the  compressor  to  settle  into 
soft sand, resulting in compressor drawing in foreign 
particles.  Never  expose  compressor  to  water  while 
running the compressor.  

IMPORTANT: 

Make  sure  compressor  sits  upright 

while  operating  compressor.      Avoid  tugging  at 
compressor  if  line  is  taut.  Instead,  move  the
compressor to the same side of vehicle as  tires  that 
are being aired up. 

IMPORTANT

:

  Always  make  sure  the  Portable 

Compressor’s 8 foot power cord is uncoiled and fully 
extended  when  using  your  air  compressor  to  avoid 
overheating the power cord.   

Summary of Contents for 40043- 400P










Reviews: