background image

SAFETY PRECAUTIONS:

1. Always inflate tires to manufacturer’s recommended tire pressures. Exercise extreme caution 

  when driving with aired-down tires. Reinflate tires before high-speed roadway travel.

2. Never exceed 20 M.P.H. when driving with partially inflated tires.

3. Never make sharp turns while driving with reduced tire pressure.

4. Re-inflate tires before high speed traveling onto roadways.

5. Use heat-resistant, minimum 200 PSI-rated working pressure extension hose. 

  Do not use aftermarket hoses with less than 200 PSI working pressure. Some aftermarket hoses 

 

  may not be suitable for use with this air compressor due to heat and pressure typically generated 

 

  by this type of air compressors.

IMPORTANT:

 Always use an Open-Ended tire chuck such as the tire chuck equipped on the 

Deflator/Inflator Coil Hose for tire inflation when using a compressor without an air tank.

CAUTION:

 Never touch the air compressor or fittings connected to the air compressor other than 

the ON/OFF switch with bare hands during or immediately after use. The extension hose and fittings 

connected extension hose will become very HOT during and after use. If necessary, wear heat 

resistant gloves to remove hose from the compressor quick connect stud.

RECOMMENDATION:

This compressor is equipped with a poppet pressure release head valve. Head pressure will slowly 

decrease (pressure will be released through the intake port of the compressor) to allow smooth 

re-starts under pressure. If compressor’s is hooked up to power source and if the power switch 

is left in the ON position for more than 7 to 8 minutes, Compressor will automatically turn on for a 

short duration (3 to 5 seconds) to recover pressure due to built-in pressure switch. This is a normal 

function of the compressor.  Always shut off power to the compressor when the compressor is 

 

not in use. 

MAINTENANCE & REPAIRS:

Your air compressor is equipped with permanently lubricated, maintenance-free motor. 

 

Never try to lubricate the compressor.  Regularly clean dust and dirt from compressor cooling fins 

and motor housing.  All repairs should be performed by Manufacturer or Manufacturer authorized 

service agencies only.

400P AUTOMATIC PORTABLE COMPRESSOR

USER MANUAL

Summary of Contents for HEAVYWEIGHT Series









Reviews: