background image

In order to protect your purchase and aid your
warranty please fill in the following form and
keep it safe for your future reference:

Model Number:

Serial Number:

Purchased From:

Date of Purchase:

KEEP

IT SAFE

Staple your receipt here:

Parameters for BlackAir Subwoofers 

BlackAir 10

BlackAir 12

BlackAir 15

RMS power

450

550

650

Peak power

1300

1600

2000

Min, Input wattage

225

275

325

Diameter in inches

10”

12”

15”

Z- Nominal Impedance in Ohms

Dual 2 Ohm

Dual 2 Ohm

Dual 2 Ohm

Revc = DC voice coil resistance in Ohms

3.6

3.6

3.6

Fo = Free air resonance frequency in Hz

40.959

34.995

32.371

Sd = Piston area in square meters

34.600

53.000

85.000

Vas = Equivalent acoustic volume in cubic litres

15.386

46.311

119.250

Cms = Mechanical suspension compliance

90.152

116.102

116.234

Mmd = Diaphram mass in grams

117.997

144.112

193.713

Mms = Mechanical mass of cone and free air load in grams

121.677

151.128

207.962

BL = The magnetic strength of the motor structure

15.111

15.37

17.796

Qms = Mechanical Q factor of driver

1.171

1.952

1.992

Qes = Electrical Q factor of driver

0.578

0.550

0.501

Qts = the system’s Q at resonance (Fc)

0.437

0.429

0.417

n0 = The reference efficiency of the system in %

0.284

0.447

0.800

SPL = Speaker’s SPL 1 watt at 1meter in dB:

86.55

88.521

90.122

Voice Coil Diameter in inches

2

2

2.5

Mounting Depth in mm

128

141

168

Mounting Diameter in mm

240

285

355

Magnet weight in oz

40

60

75

Summary of Contents for BlackAir 12













Reviews: