THE MENUS
4 RECORDING MODE (REC MODE)
Sets the recording mode.
NORMAL&P> : Choose when higher picture quality is preferred. With this setting, the recording time mode is switched in the order
:
Select a EP setting to perform High Density recording. This provides 3x more fields than Normal Density (SP).
It reduces the time interval between pictures, providing more pictures for smoother time lapse recording. With
this setting, the recording time mode is switched in the order of 6H
48H
72H
96H
5
SETTING THE NUMBER OF FIELDS IN ONE-SHOT RECORDING (ONE
Sets the number of fields to record in the One-Shot mode. When the JOG dial is turned to the right, the display will be switched in
theorderof 1
1
6 SETTING INTERVAL
TIME IN ONE-SHOT RECORDING (ONE
Sets the interval time in the One-Shot mode. When the JOG dial is turned to the right, the display will be switched in the order of
SHOT
(second)
2M 3M SHOT
<REAR TERMINAL>
D CALL OUT
END
1
SETTING THE CALL
SIGNAL OUTPUT AT THE END OF THE TAPE (CALL OUT)
CLOCK OUT
1
Enables or disables the signal that is output from the CALL terminal when the end of the tape is
REC
SERIES
reached during recording. If any abnormalities occur during recording, a CALL signal is output from
the CALL terminal on the rear panel regardless of CALL OUT setting.
END:
A signal is output at the end of the tape or when a malfunction occurs.
The signal is output when a malfunction occurs in this VCR or when the tape
has approximately 3 minutes left in 2H mode.
WRNG:
When a malfunction occurs in the VCR during recording, a CALL signal is output.
This is used in conjunction with TAPE END (FIRST TIME SET UP) to determine when the CALL signal is output as shown below.
END
settinq
- - -
STOP
Outputs a call signal at
the end of the tape
REWIND
Outputs a call signal at the end
of
the tape for 2 seconds
Outputs a call signal at the
W R N G
Outputs 3 minutes before
When a malfunction occurs in the VCR
the tape end
during recording, a call signal is output
t
t
2
SETTING THE FREQUENCY DIVISION RATIO (CLOCK OUT)
Sets the frequency division ratio of the CLOCK OUT terminal.
First, set the recording mode for the “CLOCK OUT” pulse output in the “REAR TERMINAL” menu.
REC:
When recording in any mode.
T/L-REC:
When recording in time lapse mode
or OH).
Second, select the frequency division ratio setting by turning the SHUTTLE ring. When the JOG dial is turned, the display will be
Thenumbersfromlto
60 indicate the number of frames in 2H or 6H recording mode or the number of fields in time lapse recording mode. (One frame
consists of two fields.) One field is selected when it is set to
(field).
3
SETTING THE OPERATION MODE OF THE MODE OUTPUT TERMINAL (MODE OUT)
Sets the state in which the signal output at the MODE OUT terminal is switched to the active condition. When the JOG dial is turned,
the display will be switched on in the order of REC (recording)
PLAY (playback)
POWER (power “ON”)
TAPE IN (tape is
inserted)
TAPE REMAIN (3 minutes in 2H mode before the tape end)
CLOCK ADJ (output the signal for 1 second when the
clock indicates
)
REC.
4
SETTING THE OPERATION MODE OF THE REC IN TERMINAL (REC IN)
SERIES: Recording starts when the REC IN terminal is short-circuited to ground or a
level voltage (0
is applied.
REC-START/ STOP: Recording starts when the REC IN terminal is short-circuited to ground or a
level voltage (0
applied. Should this connection be removed, recording will stop.
SYNC REC: The video signal from 3 or 13 cameras can be recorded separately by connecting a switcher. (“SYNC REC” function
available when recording in
or
mode.) Refer to “SYNCHRONOUS RECORDING” on page