background image

User Manual for ICHA Freezers 

Victory

Rev. 09/21

Victory

10

This is a cord-connected unit, and must be connected to 
its own 

dedicate

d power supply. Check the dataplate on 

the machine to confirm the voltage and per the dataplate 
use the correct fuses or HACR circuit breakers.

Power Cord

This 115 volt model is equipped with a cord and 5-15P plug 
for each of two refrigeration systems.

If a power cord becomes damaged, it must be replaced 
with the identical cord.

GFCI

Units that utilize variable speed compressor technology 
can experience nuisance tripping on Class A GFCI outlets 
which have a trip limit of 4 to 6 mA.  To avoid this 
issue in a location that requires GFCI circuit protection, 
Victory recommends using a HUBBELL Model Number 
GFRST83W 20A Heavy Duty Hospital Grade Self-Test 
GFCI Receptacle.

Follow All National and Local Codes 

This unit must be grounded. Do not use extension cords 
and do not disable or by-pass ground prong on electrical 
plug.

Initial Start Up

Plug the power cord into the proper power supply.

The cabinet will soon begin to blow warm air out of the 
top area, and cool air will flow from the inside blower.

The cabinet temperature has been set at the factory and 
should not need adjustment, however if it was changed, 
the standard setting is -25º F.

Cautions

Care must be taken whenever moving or servicing the 
unit. The refrigerant is contained in a sealed system, but if 
released it may be flammable.

After the cabinet has been installed, leveled, and cleaned 
as described above, refer to the following checklist:

 Check for proper electrical hook-up.

Cabinet MUST NOT SHARE A RECEPTACLE with another 
piece of equipment

 Check that all clearances are in line with the 
aforementioned guidelines.

 Check that cabinet is level.

* NOTE: Once the unit has been started and reaches proper 
storage temperatures, it may be loaded with product. For 
proper energy efficiency and airflow we recommend a 
minimum1” clearance between product and side walls, 4” 
clearance between product and ceiling, and 1” clearance 
from the bottom of the unit.

ELECTRICAL

5-15P Plug

Summary of Contents for CARPIGIANI ICHA-1D-S1-EW-HD-HC
























Reviews: