8
9
INITIAL SETTINGS
Initial settings page is for you to make your preferred settings up for your player. Once the initial settings
are done they are retained in the CPU of the player until otherwise modified.
COMMON PROCEDURES FOR INITIAL SETTINGS
1. Press SETUP button to access the setup menu.
2. Use the navigation buttons to select the item you want to modify, setting page with further setting
items displayed shows on the TV screen. Again use navigation buttons to make changes. Press OK
button to confirm modifications.
3. Use navigation buttons to switch to another setting on the main setting page.
4. Press SETUP button to exit main setting page.
1. SYSTEM SETUP
1.1 TV SYSTEM
- it is used to select the TV mode.
Please select this option as per your TV set.
1.2 SCREEN SAVER
- when the player is not in used for several minutes, a running DVD logo will move
across the TV screen to protect the TV screen.
Options:
On: Screen saver is enabled
Off: Screen saver is disabled
1.3 TV TYPE
- it is used to select the TV scan mode, please set as per your TV set.
Options: 4:3PS : Normal Pan & scan mode
4:3LB : Normal Letter box mode
16:9 : 16:9 wide screen mode
1.4 PASSWORD
- input password to unlock the system. The steps are as follows:
1.4.1 Enter SYSTEM SETUP, select the PASSWORD item by scrolling the down navigation button, and
then press the right navigation button to select the input box.
1.4.2 Input user's password "0000" to unlock it, in this case, select the input box again to change the
password by inputting another new four numeric numbers and then press OK button to confirm. When
the password is changed, you are needed to input the new one to unlock the system.
1.4.3 Once you forget your own password, use the supervisor's password "8200" to unlock it.
NOTE: If wrong password was input in unlock status, the system will lock.
1.5 RATING
- Set the rating of this player. If you want to change the rating of parental lock, please input
the password to unlock first.
Options: 1 KID SAFE / 2 G / 3 PG / 4 PG 13 / 5 PG-R / 6R / 7 NC-17 / 8 ADULT
1.6 DEFAULT
- Reset to factory settings.
Options: RESTORE
2. LANGUAGE SETUP
2.1 OSD LANGUAGE
- It is used to select different On Screen Display language for different user.
2.2 AUDIO LANG
- Select preferred audio language. (DVD only, need disc software support)
2.3 SUBTITLE LANG
- Select preferred subtitle language. (DVD only, need disc software support)
2.4 MENU LANG
- Select preferred disc menu language. (DVD only, need disc software support)
3. VIDEO SETUP
3.1 BRIGHTNESS
- to set the brightness for the display.
Options: 0/2/4/6/8/10/12
3.2 CONTRAST
- to set the contrast effect for display.
Options: 0/2/4/6/8/10/12
3.3 HUE
- to set the colour impression for display.
Options: -6/-4/-2/0/+2/+4/+6
3.4 SATURATION
- to set the saturation level for display.
Options: 0/2/4/6/8/10/12
4. SPEAKER SETUP
4.1 DOWNMIX
Options: LT/RT - Left/Right mix mode
STEREO - Select this option if you don't have a 5.1 channels amplifier.
DISC HANDLING PRECAUTIONS
Hold the disc by the edge so the surface will not be soiled with finger prints. Finger prints,
dirt and scratches can cause skipping and distortion.
Do not write on the label side with a ball-point pen or other writing utensils.
Do not apply benzine, thinner, and liquid that prevents against static electricity.
Be careful not to drop or bend the disc.
Install only one disc on the disc tray.
Do not try to close the disc tray when the disc is not installed properly.
Be sure to store the disc in its case when not in use.
