White: PRIVACY-ZONE
Position movement
Blue: PRIVACY-ZONE Size
enlargement or reduction
For PRIVACY-ZONE Confirm,
long press SET button
1. Move the cursor to the letter required by using the
Set-Up button.
2. Select an ID from A,B~Y,Z, a,b~y,z, 0,1~8,9 by using
the LEFT and RIGHT buttons.
3. Repeat the above steps until the ID is complete.
1. Select the position where the ID is to be displayed by
using the LEFT and RIGHT buttons.
VIDEO OUT
: Move the cursor to select the video system.
VIDEO STANDARD: You can control NTSC / PAL, Video
level, Sync level, Burst level.
DZOOM
: Digital P/T/Z are used to create a zoom lens
effect. Zoom Factor (1X to 8X), Pan(±100%, center of
image can be moved to left and right edges of screen),
Tilt (±100%, center of image can be moved to top and
bottom edges of screen)
MOTION
: This product has a feature that allows you to
observe movements of objects in on the screen, hence a
single individual can conduct supervision efficiently.
The camera detects an object's movement by sensing
disparity of the outline, and level of brightness and color.
White: MOTION ZONE Position movement
Green: MOTION ZONE Size enlargement
Red: MOTION ZONE Size reduction
For MOTION ZONE Confirmation, press and hold the
SET button
PRIVACY SETUP
: Mask an area you want to hide on the
screen.
SYNC
: Two synchronization modes are available,
INTERNAL and EXTERNAL LINE-LOCK. In LINE-LOCK
mode, it synchronizes the video signal between cameras
without a synchronous generator.
The line-lock synchronization is only used in areas of
60Hz (NTSC) / 50Hz (PAL).
- INT : Internal synchronization
- LL : External line-lock synchronization
If 'LL' is selected, it can be adjusted to the desired phase.
Press the SET button.
Adjust to the desired phase from 0 to 624.
How to Use the Camera
How to Use the Camera
How to Use the Camera
How to Use the Camera
Saves all the setting menus and then exits.
If you have trouble operating your camera, refer to the
following table.
If the guidelines do not enable you to solve the
problem, contact an authorized technician.
EXIT MENU
TROUBLESHOOTING
Problem
Solution
Nothing appears
on the screen.
The image on the
screen is dim.
The image on the
screen is dark.
The camera is not
working properly,
and the surface of
the camera is hot.
The DAY/NIGHT
menu does not
work.
The Motion
Detection function
does not work.
Color is not
correct.
The screen flickers
continually.
• Check the power connections.
• Check the VIDEO signal line
connection.
• Make sure the lens is clean. Clean the
lens with a soft clean lint free cloth.
• Adjust the monitor contrast &
brightness controls.
• Re-position the camera if necessary.
• Adjust the contrast control of the
monitor.
• If you have an intermediate device, set
the 75
Ω
/ Hi-z properly.
• Check that an appropriate power
source is connected to the camera.
• Check that AGC in the EXPOSURE
menu is set to 'OFF'.
• Check that MOTION DET in the
SPECIAL SETUP is not set to 'OFF'.
• Check the WHITE BAL settings in the
SETUP menu.
• Check that the camera is not facing
toward the sun.
FLIP
: OFF / HORIZ / VERT / BOTH selectable
SHARPNESS
: The outline of the video image
becomes cleaner and more distinctive as the level of
sharpness increases. If the level goes up excessively,
however, it may affect the video image and generate
noise.
- The available level range is -8 ~ 8
COLOR GAIN
: To control the color level in the video.
- The available level range is -8 ~ 8
GAMMA
: Users can change the gamma setting
between 25 and 100.
When the SETUP menu screen is displayed, select
'SPECIAL' by using the Up and Down buttons so that
the arrow indicates 'SPECIAL'.
CAMERA ID
: User can enter a unique name for the
respective camera.
The maximum length of the ID is ten characters.
• You can turn the camera ID ON and OFF with the
selector.
If you select ON, the entered camera ID is
displayed at the selected position in the video
picture (normal operation).
• Please select the setup button while in ON mode.
• Select the desired position with the selector.
SPECIAL
CONTACT INFORMATION
For technical assistance with this product, please
contact the supplier from whom the product was
purchased.
For OEM inquiries:
North/South America
Europe
37M Lark Industrial Parkway
Neutronenlaan 4
Greenville, RI 02828
NL-5405 NH Uden,
USA Netherlands
Please visit our website at: http://www.videologyinc.com
VIDEOLOGY IMAGING SOLUTIONS is an ISO 9001 registered
video camera developer and manufacturer serving industrial,
machine vision, biometric, security, and specialty OEM
markets. Videology designs, develops, manufactures, and
distributes video, image acquisition, and display technologies
and products to OEMs worldwide.
03/07/11 INS-20C708W Rev A Preliminary
