66251990 - V1.1 - 15/07/21
- 3 -
Kristallo Series
Art. KRV82 - KRV84 - Installation instructions
NUMBER OF RINGS
1. Press and keep pressed
button for more than 3 seconds to enter Number of rings
programming mode: the
LED turns on and the unit emits a “beep“.
2. Press
button as many rings as required: the unit emits a “beep“ every time the button is pressed.
I.E.
: press 3 times for 3 rings.
3. Wait for some seconds: the
LED turns off and the unit emits a “beep“ that confirms the new setting is properly stored.
4. After 5 seconds without any user action the unit returns to stand-by mode.
Default value
3 rings
Max value
9 rings
PRIVACY SERVICE DURATION
1. Press and keep pressed
button for more than 3 seconds to enter Privacy service
duration programming mode: the
LED turns on and the unit emits a “beep“.
2. Press
button as many times as required. Each press is equal to 15 minutes: the
unit emits a “beep“ every time the button is pressed.
I.E.
: press 4 times for 1 hour, 12 for 3 hours.
Note:
To program infinite privacy time don’t press any button until the unit emits a “beep” to confirms the setting.
3. Wait for some seconds: the
LED turns off and the unit emits a double “beep“ that confirms the new setting is properly stored.
5. After 5 seconds without any user action the unit returns to stand-by mode.
Default value
Infinite
Max value
20 hours
Increase
15 minutes
VIDEOPHONE ADDRESS – SW1.1..7
The table below shows how to set the address of the videophone. Considering that ON = 1 and OFF = 0, multiply
each digit for the relevant decimal weight then sum values obtained to get the address:
E.g.
as highlighted in
the table OFF, ON, OFF, OFF, ON, OFF, ON in binary is equal to 0100101 then multiplying each digit for the rele-
vant decimal weight you obtain the address that is 37.
SWITCHES STATUS
BINARY CODE - DECIMAL WEIGHT
ADDRESS
7
6
5
4
3
2
1
64
32
16
8
4
2
1
OFF
OFF
OFF
OFF
OFF
OFF
ON
0
0
0
0
0
0
1
1
OFF
OFF
OFF
OFF
OFF
ON
OFF
0
0
0
0
0
1
0
2
OFF
OFF
OFF
OFF
OFF
ON
ON
0
0
0
0
0
1
1
3
OFF
OFF
OFF
OFF
ON
OFF
OFF
0
0
0
0
1
0
0
4
OFF
ON
OFF
OFF
ON
OFF
ON
0
1
0
0
1
0
1
37
ON
ON
ON
ON
ON
ON
ON
1
1
1
1
1
1
1
127
Note:
The maximum number of units allowed is 100 but the address of each unit can be a value between 1 and 127.
ON
1 2 3 4 5 6 7
8
SW1.1..7
ENABLE ART. 2305 RELAY ACTIVATION DURING STAND-BY
To enable the Art. 2305 relay activation
when the device is in
stand-by,
set up dip 8 of
SW1
as shown in the table to the right.
This enables you to activate the Art. 2305 auxiliary relay (if pres-
ent on the system) using the
,
,
and
that activate re-
spectively the relay’s 1, 2, 3 and 4.
SW1
Setting up
ON
1
3
5
7
2
4
6
8
Dip 8 =
ON
Enable Art. 2305 relay
activation
ON
1
3
5
7
2
4
6
8
Dip 8 =
OFF
Disable Art. 2305 relay
activation
Art. KRV82-KRV84
3.5” Hands free videomonitor
Summary of Contents for Kristallo Series
Page 21: ...66251990 V1 1 15 07 21 21 ...
Page 22: ...66251990 V1 1 15 07 21 22 ...
