background image

CAUTION!

 

Risk of crushing

The cover plate shifts in parallel with the wall surface

during the height adjustment. Due to this, there is the risk

of crushing in the areas above and below the cover plate.

n

Keep your hands away from the dangerous areas.

When the actuating button is pressed and there is a load of at

least 60 kg (body weight and WC ceramic), the ceramic is lowered by a

maximum of 80 mm.

When the actuating button is pressed and there is no load on the WC

ceramic, the WC ceramic is raised by a maximum of 80 mm by the gas

pressure spring.

2.3.3

Compatible components

The WC element is compatible with all common WC ceramics, even

with larger projection (barrier-free).

The WC element can be extended by the following compatible compo‐

nents:

n

Prevista Dry fixing element

n

Prevista Dry fixing set model 8570.36

n

Prevista Dry fixing set model 8573

n

Fixing set model 8180.73

n

Odour extraction via Prevista flushing pipe elbow with ventilator con‐

nection 3H

n

Accessory set connection electronic model 8655.11

Mount the components in accordance with the respective instructions

for use.

The odour extraction system is suitable for reducing odour nuisance in

indoor bathrooms and highly frequented toilet facilities. The odour

extraction system is connected to the ventilation system directly.

Lowering WC

Lifting WC

Odour extraction

Product information

Prevista Dry WC element ceramic height individually adjustable

7

Summary of Contents for 8521.32











































Reviews: