Viega LLC
585 Interlocken Blvd.
Broomfield, CO 80021
Phone (800) 976-9819
www.viega.us
Product Instructions
Viega PureFlow
®
Crimp Washing
Machine and Ice Maker Boxes
PI-PF 589095 1019 Crimp Washing Machine Ice Maker Boxes (EN ES FR)
Models 2872.8ZL, 2872.9ZL, V5073, V5073.5
EN
Product Instructions
Crimp Washing Machine and Ice
Maker Boxes
This document is subject to updates. For the most current
Viega technical literature please visit www.viega.us.
A
C
B
D
F
H
E
G
1
3
2
4
5
EN
Viega PureFlow Crimp Washing
Machine and Ice Maker Boxes
Viega products are designed to be
installed by licensed and trained plumbing
and mechanical professionals who are
familiar with Viega products and their installation.
Installation by non-professionals may void
Viega LLC’s warranty.
1
A. Stud
B. Face plate
C. Backing board fastened between studs
D. Valve outlet
E. Solvent cement drain connection
F. Viega PureFlow Crimp
G. PureFlow pipe
H. Wall material
2
Position the box between studs at the
desired height.
3
Ensure that the front edge of the box is flush
with wall. Secure box to a backing board with
screws, or to the front of the stud(s) using the
nailing ear(s). If necessary, cut or punch opening
on bottom of box for 2" plastic drain pipe and
solvent cement pipe connection on bottom of box
(washing machine boxes only).
4
The tubing should be cut squarely and evenly
without burrs. Uneven, jagged or irregular cuts will
produce unsatisfactory connections.
5
Connect Viega PureFlow PEX tubing to Viega
PureFlow Crimp barb(s) on valve(s).
6
Slide the crimp ring onto the tubing and insert the
fitting into the pipe to the shoulder or tube stop.
7
Position the ring ⅛" to ¼" from the end of the tubing.
8
The ring must be attached straight. Center the
crimping tool jaws exactly over the ring. Keep the
tool at 90° and close the handles completely.
9
When checking crimp connections with a
caliper (GO/NO GO gauge), push the gauge
straight down over the crimped ring. Never slide
the gauge in from the side. Do not attempt to
gauge the crimp at the jaw overlap area. The
overlap area is indicated by a slight removal of
the blackening treatment. A crimp is acceptable if
the GO gauge fits the ring and the NO GO does
not. A crimp is unacceptable if the GO gauge
does not fit the ring or the NO GO gauge does fit.
An incorrect crimp must be cut out of the tubing
and replaced. If you check the crimp connections
with a micrometer or caliper, use the dimensions
shown in the chart above.
10
When installing drywall, cut an opening (6⅝" W x
7
1
/
16
" H for the washing machine box and 5¼" W
x 5¼" H for the ice maker box). Any gap between
the drywall and the side of the box must be filled
with drywall compound.
11
Push face plate into the box until the plate is flush
against the wall material.
CAUTION!
Do not crimp twice!
Zero lead identifies Viega products meeting
the lead free requirements of NSF 61-G
through testing under NSF/ANSI 372 (0.25%
or less maximum weighted average lead content).
6
6
90°
1
/
8
” to ¼”
7
9
8
10
11
ES
Instrucciones del producto
Cajas para lavadoras y
máquinas de hacer hielo Crimp
Este documento está sujeto a actualizaciones. Para obtener la
documentación técnica más reciente de Viega, visite www.viega.us.
FR
Instructions produit
Boîtiers pour machine à laver et
machine à glaçons Crimp
Le présent document est soumis à des mises à jour. Pour
consulter les manuels techniques Viega les plus récents, veuillez
visiter www.viega.us.
ES
Cajas para lavadoras y máquinas de
hacer hielo Viega PureFlow Crimp
Los productos de Viega están diseñados
para ser instalados por plomeros y
mecánicos profesionales, capacitados
y con licencia, que estén familiarizados con los
productos Viega y su instalación.
La instalación
realizada por personal no profesional puede
anular los términos y condiciones del producto
de Viega LLC.
1
A. Tabique
B. Placa frontal
C. Tablero fijado entre tabiques
D. Salida de válvula
E. Conexión de drenaje de cemento solvente
F. Viega PureFlow Crimp
G. Tubo PureFlow
H. Material de pared
2
Posicionar la caja a la altura deseada,
entre tabiques.
3
Asegúrese que la cara frontal de la caja se
encuentre en el mismo plano que la pared. Fijar
la caja con tornillos de un tablero o en la parte
frontal del tabique(s), con ayuda de la(s) oreja(s)
de fijación. Si es necesario, recortar o perforar
en la parte inferior de la caja una abertura para la
tubería de drenaje de plástico de 2" y la unión de
Zero Lead identifica a los productos
Viega que cumplen los requerimientos de
la NSF 61-G mediante la realización de
ensayos de acuerdo a NSF/ANSI 372 (contenido de
plomo promedio ponderado máximo de 0.25 % o
menos).
