background image

Sirijus 20, 30 

 

 

 

 

 

 

 

 

          Sirijus 20, 30 

 

                   Sirijus 20, 30 (13.05) V1 LT           Sirijus 20, 30 (13.05) V1 LT 

Dear Buyer

!  

 
Thank You for purchasing our company’s article and for the confidence in products of JSC 
“UMEGA”.  
 
We wish you success in use of it! 

JSC “UMEGA” 

 
 

1.GENERAL INFORMATION 

 
Solid fuel boilers “SIRIJUS-20”, “SIRIJUS-30” (hereinafter – the boiler) are intended for: 
- heating of residential houses,  
- heating of administration offices or industrial premises.  
 
Fuel suitable for the boiler *:  
- wood,  
- coal 
- peat briquettes,  
- compounds of the above listed fuels.  
 
* fuel wetness not exceeding 20%  
 
Boiler  “SIRIJUS”  are  designed  in  compliance  with  all  the  applicable  up-to-date  economic, 
environmental, and safety requirements and have good performance characteristics. 
 
Shell is a welded carbon steel sheet of 5-4 mm thickness, with channels where water circulates. 
The boiler has:  
- Primary and secondary air supply,  
- high degree of heat insulation,  
- a high efficiency coefficient. 

 
 
 
 
 
 
 
 
NOTICE!  Before  installation  and  operation  of  the  heating  boiler-oven,  please  read  this 
manual.  This  will  help  You  to  properly  install  and  the  most  effectively  use  the  product 
purchased and to avoid accidents. 
When  buying  the  boiler,  please  read  terms  of  warranty,  make  sure  that  the  certificate  of 
acceptance is filled in completely and correctly. 
 
 
 
 

 

 

12. WARRANTY CLAIM FORM

 

 

To General Director of JSC “Umega” 

 

I .................................................................................. have acquired the product made by 

(name, surname or name of company) 

your company:......................................................................., serial No. 

…………......…………., … 

(product name) (date of manufacture)  
…...…………………………………………... ……………………………………………….…………… 
(date, place of purchase, name and number of the purchase document)  

 

I  have  read  the  product  data  sheet  and  hereby  declare  that  the  product  has  been  installed  in 
accordance with the requirements, established by the manufacturer in the data sheet, and is used 
for its intended purpose, without violating the requirements of the operation manual. Given that, I 
have the following claim against this product:  
…………………….…………………….…………………….......…………………..………………….  
…………………………………………………………………….......………………………………….  
…………………………………………………………………………... ...………………………….…  
……………………………………………………………………………….......………………….……  
…………………………………………………………………………………….......………….………  
………………………………………………………………………………………….......….…………  
…………………………………………………………………………………………….........…………  
…………………………………………………………………………………………….……........……  
…………………………………………………………………………………………….……………....  
 

…………………………………………………………………………………………….……………...  

…………………………………………………………………………………………….……………....  
Assuming that the deficiencies, expressed in the claim, were affected by defects of your product, 
please send your representative to inspect the product installed, detect the defects, and eliminate 
them. If these deficiencies are found to have occurred due to improper connection or use of the 
product, or there are no defects under the warranty, I shall undertake to cover travel expenses for 
the arrival of your representatives (0.8 Lt/km) and the time spent on travel and on-site inspection 
30 Lt/h) to each employee of the service team (no more than to three employees). 

 

If, within  7  calendar days,  I  fail  to  cover the  above  expenses,  I agree  to  recovery  of  them 
against me in the manner prescribed by the legislation of Lithuania. 

 
My address ……………………………………………., phone…. ……………………. 
……………………………………………………………………………………………..  
Name, surname    

 

 

 

Signature 

 
 
 
 
 

 
 
 
 
 

Summary of Contents for SIRIJUS 20










Reviews: