Viesa AGRO Installation Manual Download

Page: 3 / 44

Index

INSTALLATION MANUAL

1- ECOLOGICAL COOLER

...............................................................................................................5

2.2- UPHOLSTERY COVER AND ACCESSORIES

1.1- LOCATION OF PARTS AND COMPONENTS

1.2- TECHNICAL CHARACTERISTICS

..........................................................................6

................................................................................................6

2- MAIN COMPONENTS

.............................................................................................................7

2.1- EVAPORATOR UNIT

.......................................................................................................................7

............................................................................14

2.3- POWER AND CONTROL MODULE

.........................................................................................14

2.4- BOARD INDICATIONS

2.5- UPHOLSTERY COVER

2.8- WATER PUMP

.......................................................................................................17

..................................................................................................................18

.................................................................................................................................27

2.9- LEVEL SENSOR

...............................................................................................................................28

3- CONNECTIONS

...........................................................................................................................29

3.1- HYDRAULIC

..................................................................................................................................29

3.2- ELECTRICAL

..................................................................................................................................30

2.6- WATER TANK

................................................................................................................................20

2.7- WATER TANK SUPPORT (OPTIONAL)

.................................................................................25

2.10- WATER PUMP COVER

...............................................................................................................28

5- RECOMMENDATIONS TO THE INSTALLER

.....................................................................34

6- GENERAL MAINTENANCE

.......................................................................................................34

7- REPLACEMENT OF THE MAIN COMPONENTS

..............................................................36

8- FAILURE LOCATION GUIDE

.............................................................................................39

4- UNITS WITH TILT CABINS

....................................................................................................32

Summary of Contents for AGRO













































Search results

Summary of Contents for AGRO

Reviews:

Related manuals for AGRO

Brands by name

Popular brands

Viesa AGRO, Installation Manual

Search results

Summary of Contents for AGRO

Reviews:

Related manuals for AGRO

Brands by name

Popular brands