23
ENGLISH
CD/USB/SD Android Radio
22
Operation
Location of Keys
1. Release button
2. Volume knob (when rotated)
SEL button (when pressed)
3. Liquid crystal display
4. Disc slot
5.
(tune/seek/track down)
6. DISP button
7. BND +
button
Reject button
8.
Eject button
9.
(tune / seek / track up)
10. AMS button
11. Auxiliary input jack
12. USB interface
13. MODE +
button
(pick up phone) button
14. AF/PTY ENTER button
15. Reset button
16. EQ/TA button
17. 6 DIR+ button
18. 5 DIR- button
19. 4 RDM button
20. 1-6 preset buttons
21. 3 RPT button
22. 2 INT button
23. 1 PAU button
24. Memory card interface
25.
MUTE
SWITCHING ON/OFF THE UNIT
Press
/MUTE button (25) to switch on the unit.
When system is on, press and hold
/MUTE button
(25) to turn off the unit.
FACEPLATE RELEASEl
Press the release button (1) to detach the removable
faceplate.
SOUND ADJUSTMENT
Rotate the volume keys ( 2 ) is to reduce the sound
volume keys Rotate Right ( 2 ) is to increase the
volume. Also pressing the volume keys can be
selected.
SYSTEM SETTING
Press and hold the volume button (2) on the front
panel to enter system setting mode. Then briefly
press the volume button (2) to select the item you
want to change and rotate the volume knob (2) to
change the corresponding setting.
1) BEEP ALL/OFF/2ND
Use the volume knob (2) to set Beep sound ALL, OFF
or 2ND.
- BEEP 2ND mode:
The beep is only generated when all function (2nd)
keys are pressed & held (1 sec).
- BEEP ALL mode:
The beep is generated when every key is pressed.
- BEEP OFF mode:
The beep is disabled.
2) AREA EUR/USA
In radio mode, use the volume knob (2) to set the
different area frequency spacing.
3) TA SEEK/ALARM
Use the volume knob (2) to set TA SEEK or TA
ALARM.
Traffic announcements:
n
TA SEEK: With activated TA function the unit
searches for a station with traffic announcements.
n
TA ALARM: No automatic station search. The
unit sounds a beep tone if no traffic information is
received and NO TP/TA is displayed. SEEK PI is
displayed if the selected station does not transmit an
RDS signal.
4) PI SOUND/MUTE
Use the volume knob (2) to set PI SOUND or PI
MUTE.
Moving into an area where two stations with identical
AF, but different Pl code (PI = program information)
are received destabilizes reception. In this situation
you have two options:
n
PI SOUND: To change stations the other station is
played for less than one second.
n
PI MUTE: The other station is muted.
5) RETUNE L/S
Use the volume knob (2) to set RETUNE L or
RETUNE S.
Delay for automatic search with traffic
announcements and/or program information:
n
S (short) after approx. 30 seconds;
n
L (long) after approx. 90 seconds.
6) MASK DPI/ALL
Use the volume knob (2) to set MASK DPI or MASK
ALL.
Setting to mask station during search:
n
DPI : Alternative frequencies with different Pl code
are excluded from the search.
n
ALL : Alternative frequencies with different Pl code
and no RDS information with high signal level are
excluded from the search.
NOTE: When selecting AREA USA in system setting,
the (3)/(4)/(9)/(6) four setting items are invalid and
invisible.
SET THE CLOCK
Briefly press the DISP button (6) until the clock is
shown on the display. Then hold the DISP button
until the clock flashes. Then briefly press DISP button
to select minutes or hours to adjust and rotate the
volume knob (2) to change the value.
DISPLAY INFORMATION
Press DISP button (6) to operate as the conversion of
each display mode.
EQUALIZATION
Press EQ/TA button (16) briefly to turn on equalization
function and to select desired audio mode. There are
five kinds of modes as below:
FLAT, CLASSIC, POP, ROCK, EQ OFF
Basic Operation
Summary of Contents for VC-HA920BT
Page 30: ...www vieta es ...
