®
®
module and antenna
How to install WLAN
Step
1
Step
2
Step
3
Step
4
Step
3
Preparation before the installation setup
Step
5
Step
2
Step
4
8
Install the WLAN USB module (EMIO-1533-00A1) and secure it
Insert the WLAN port connector into the antenna
Gently connect the mini coaxial cable of the
Attach the WLAN board to board cable to the WLAN USB module.
The front side panel of VZ-PRO-MINI has four
If using a network, connect the Ethernet cable to
Attach the Ethernet cable from LAN port of the
Plug the audio cable into the Line-out jack on
Plug the power cable into the DC-In jack on
Plug the Video Wall Mini power cord into an
must be done, all components and network are
power of VZ-PRO-MINI.
port numbers on Video Wall Mini (e.g. video wall
The VZ-PRO-MINI has a HDMI-IN port which can support external
digital/video sources such as Notebook PC, DVD player and etc.
For more information, please contract our sales representative.
For more information on
this and other ViewZ
products, please visit
www.viewzusa.com
Remove the 3G/3.5G antenna hole cover from the right side panel
1. Read first this Quick Setup Diagram
2. This Quick Setup Diagram is only intended to
5. VZ-PRO-MINI is a little bit heavy. Avoid
3. Ensure that all items, peripherals, cables
4. Make sure the power cord of VZ-PRO-MINI
6. Do not place the system on unstable
7. If you are unfamiliar with the installation
section before taking any action.
be used as a reference guide for setting up
dropping the system accidentally, handle
and tools needed are present before
is unplugged before the installation setup.
surfaces or walls.
process consult qualified personnel.
using the VZ-PRO-MINI system. It is not
it tightly directly on its body chassis and
starting the installation setup.
required or intended to be a step
by step procedure for the setup.
avoid holding it on any external I/O connectors.
Gently connect the mini coaxial cable of the 3G/3.5G port
of the chassis.
connector to the mini RF connector on the 3G/3.5G module.
Once the 3G/3.5G module has been fully inserted, push down the
Insert the 3G/3.5G port connector into the antenna hole from the
with two screws. Then remove the antenna WLAN hole cover
hole from the inside of the chassis. Insert the
WLAN port connector to the mini RF
Then attach the other end of the cable to the “JUSB2_3” pin
HDMI ports (HDMI 1 ~ HDMI 4). Connect the HDMI
the LAN port on Video Wall Mini. Then connect the
control Server to the LAN port on Hub/Router.
VZ-PRO-MINI.
VZ-PRO-MINI.
electrical outlet. Make sure all other connections
properly set up and ready before turning on the
display number 1 and 2 must be connected to HDMI
Copyright © VIEWZ USA. All rights reserved.
from the right side I/O panel of the chassis.
washer, fasten it with the nut and install the
connector on the WLAN USB module.
header of the mainboard.
cables of video wall displays to its designated HDMI
other end of the cable to the Hub/Router.
1 and HDMI 2 ports respectively).
external antenna.
module until the screw hole aligns with the standoff hole. Then
inside of the chassis. Insert the washer and fasten it with the nut
secure the module with screws.
then install the external antenna.
Quick Setup Diagram
Connecting the video wall display
Connecting to the network via cable wire
Connecting the control server
Connecting the speaker
Plug in the power adapter
ViewZ USA
177 W. Orangethorpe Ave., Placentia, CA 92870
Tel. 714.996.1177, Fax. 714.996.1138
Specification subject to change without notice.
sales@viewzusa.com
q
w
e
r
t
