background image

Accidently without flame, LPG may not reach the confined area near the cylinder where 

LPG Detector is installed and LPG Detector may not detect such leaks as gas molecules 

do not reach the sensor. To avoid this, install as per Fig-1 or Fig-2 above. 

 

Directly above the gas stove 

 

Places where water can splash on the unit 

 

Power ON TSGC230 

 

5V 1 Amp adapter is provided with the device.

 

 

Once installation of TSGC230 is done, Connect micro USB cable to device 

 

 

Connect adapter  in 230V AC socket and Power ON 

 

 

6.

 

Operation 

Warm up period: 

 

When device is Power ON or reset, gas sensor need to preheat for fixed duration. This mode 
called as warm-up mode.  

 

Device doesn’t sense Gas and test button didn’t work during warm-up mode 

 

Device stays in warm-up mode for first 70s. 

 

During this time Gas and heat LED blinks together. 

Sense mode: 

 

During this mode gas sensor sense the surrounding environment and give alerts if gas 
detected. 

 

When Gas is sensed above 2.5% LEL systems gives visual indication as per the LEL level on 
the corresponding LED in  

 

When gas leak is detected, system gives visual indication, audible alarm & sends the Alert to 
user on portal. 

 

The Gas Leak LED turns ON and an audible buzzer remains ON. Once the gas is dispersed, 
alarms get reset 

 

During this mode, Gas Leak and Heat LED flash alternately. 

 

During Sense mode, TSGC230 measures the ambient temperature and gives visual 
indication. 

 

When the temperature rise above 60

 C is detected, Heat LED turns ON and audible buzzer 

remains ON. 

 

Sr. 
No. 

Mode 

Gas, Heat All LEL LED status 

Portal alert status 

Warm up 

All LEL LEDs are OFF 
GAS and Heat blink together 
Buzzer off 

No alert send on portal 

Sense Mode 

GAS and Heat LED blinks alternate 

LEL LEDS OFF if Gas detection is less 
than 2.5% LEL 
Buzzer OFF if Gas detection is less than 
2.5% LEL 

No alert sent on APP 

2.5% LEL 
Gas detect 

GAS and Heat LED blinks alternate 

2.5% LEL LED ON continue 
All other LEL LED off 
Buzzer ON for 0.2s and OFF for 0.8s 

2.5% LEL alert sent on APP 

5% LEL Gas 

Detect 

GAS and Heat LED blinks alternate 
2.5%  and 5% LEL LED ON continue 

All other LEL LED off 
Buzzer ON for 0.6s and OFF for 0.4s 

5% LEL alert sent on APP 

7.5% LEL 
Gas Detect 

GAS and Heat LED blinks alternate 
2.5% ,5% and 7.5% LEL LED ON 
continue 
All other LEL LED off 

Buzzer ON for 0.8s and OFF for 0.2s 

7.5% LEL alert sent on APP 

10% LEL Gas 
Detect 

GAS LED continue ON and Heat LED OFF 
All LEL LED continue ON 
Buzzer ON for 1s and OFF for 0.1s 

10% LEL alert sent on APP 

Test Button 
pressed and 
hold for more 

GAS LED continue ON and Heat LED OFF 
All LEL LED continue ON 
Buzzer ON for 1s and OFF for 0.1s 

10% LEL alert sent on APP 

Summary of Contents for TrueSafe Gas Cloud
















Reviews: