VIGO VG6072 Installation Manual Download

Page: 1 / 16

This Installation Guide uses the following symbols to indicate important information.
Always observe the instructions indicated by these symbols.

VIGO INDUSTRIES INSTALLATION GUIDE FOR

SHOWER ENCLOSURE (MODEL VG6072)

Instructions that, if ignored, could result in death or serious personal injury caused by
incorrect handling or installation of the product. These instructions must be observed for

safe installation.

Maintenance and other important non-personal injury and non-material damage instructions

or statements that should be observed.

It is highly advised to dry fit the unit prior to any installation.

IMPORTANT

SAFETY PRECAUTIONS

WARNING

*VIGO reserves the right to modify/update all hardware and glass components based on

bettering the product for the end user's experience. If you have any questions contact VIGO

Tech Support at 1-866-591-7792.

Summary of Contents for VG6072

















Search results

Summary of Contents for VG6072

Reviews:

Related manuals for VG6072

Brands by name

Popular brands

VIGO VG6072, Installation Manual

Search results

Summary of Contents for VG6072

Reviews:

Related manuals for VG6072

Brands by name

Popular brands