Description
Enter Digits
+ Location
Security Code (default = 845464) ………………………………….......................
6 digits (0-9)
+ #47
Bypass Code (blank = disabled, default = enabled/1234) …………………........
4 digits (0-9)
+ #48
Record messages 0-7 (press Touch Tone “
Q
”
to stop recording) ......................
Q
10 -
Q
17
Playback messages 0-7 (press Touch Tone “
Q
”
to stop message playback) ....
Q
20 -
Q
27
Erase messages 0-7 .........................................................................................
Q
#0 -
Q
#7
Erase all messages ...........................................................................................
Q
#8
Transfer Message Repeat Count (00 = Disable/menu message 5,
01-99 = Enable, Default = 01) ...........................................................................
2 digits (00-99)
+ #20
Maximum Ring Count before Auto Disconnect (01-99 rings, 00 = Disabled,
Default = 20 rings) .............................................................................................
2 digits (00-99)
+ #30
Maximum Music On-Hold Time before Re-Ring (00-99 min, 00 = Disabled,
Default = 05 min) ...............................................................................................
2 digits (00-99)
+ #40
Music On-Hold Command (##) Enable/Disable (00 = Disable, 01 = Enable,
Default = Enable) ..............................................................................................
2 digits (00-01)
+ #41
Local Programming Command (
Q
) Enable/Disable (00 = Disable,
01 = Enable, Default = Enable) .........................................................................
2 digits (00-01)
+ #42
Ring Delay (1-20 rings. 00 = disabled/answer after 1st ring and play Greeting
message, Default = 00) .....................................................................................
2 digits (00-20)
+ #50
Maximum Message Playback Time (00 = Disable, 01-99 minutes,
Default = Disable) …….......................................................................................
2 digits (00-99)
+ #60
Automatic Ring Transfer (00 = Disable, 01 = Enable. Default = Enable) ……...
2 digits (00-01)
+ #70
Touch Tone Ring Transfer (00 = Disable, 01 = Enable. Default = Enable) …….
2 digits (00-01)
+ #71
Caller ID Enable/Disable (00 = Disable, 01 = Enable. Default = Enable) ……..
2 digits (00-01)
+ #80
90V Message Playing Enable/Disable (00 = Disable, 01 = Enable.
Default = Disable) ..…........................................................................................
2 digits (00-01)
+ #90
Forced hang-up .................................................................................................
##7
Clear message memory configuration
(Caution: This will erase all
messages)
........................................................................................................
Q
##
Message Memory 0-760 seconds (default = 0: Day 120 sec, 1-4: Menu 110
sec each, 5: Transfer 110 sec, 6: Night 60 sec, 7: Goodbye 30 sec) ................
3 digits
(000-760)
+ #00 - #07
* Master / slave unit number (00 = master, 01 - 63 = slave number,
default = 00) ......................................................................................................
2 digits (00-63)
+ #10
* Number of slaves (programmed in master unit only) (00-63, default = 00) ....
2 digits (00-63)
+ #11
** Reset programming to factory default settings
(Caution: This will erase all
messages)
........................................................................................................
###
D. AR-1 Quick Programming Features
(after accessing
Programming Mode
, see section
A
on page 3)
* Caution:
The slave unit number must be programmed separately into each slave unit. Numbers must be
programmed in sequential order. Total number of slave units must be programmed into master unit and must
match the total number of slave units. See page 6 section V.
** Note:
The values programmed in the master/slave memory locations “
#10
” and “
#11
” are not affected by the
“
###
” reset programming to factory default settings command.
Exiting Programming:
To exit programming simply wait 20 seconds from the last programming command and
the unit will beep 3 times. This indicates the
AR-1
has exited the programming mode.
Note:
To eliminate waiting
20 seconds, you can also exit programming after the last programming command by entering “
##7
”.
5
