Model CTG-1 (DOD# 460) with CTGF-BKD Software
PM
TIME
/ CANCEL
-
+
MODE
ALERT TONES
SINGLE
DOUBLE
TRIPLE
VIKING
©
MODEL CTG-1
LOCK
SET DAY
SET TIME
SET EVENTS
REVIEW/CANCEL
CLOCK CONTROLLED
TONE GENERATOR
VOL
9V BATTERY
BACKUP
1 2 3 4 5 6 7 8 9 10 11 12
LED1
S1
C
LED3 LED2
C C
1
3
2
ON
VIKING
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ENTRY CONTROLLER
WITH CALL FORWARD
POWER 13.8V AC
MODEL C-250
AUT
O
ANSWER
1
EARTH GND
1
TRIGGER MODE
2
LEARN MODE
3
POWER
CALLING
LINE IN
2
3
PHONES
4
5
ENTR
Y
6
7
TRIGGER
INPUT
8
9 10 11 12
DOOR
STRIKE
N.C.
N.O.
COM
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Accessing the Programming Mode
The
C-250
can be programmed from any touch tone phone connected to the house phone port or by calling into the
unit from a remote touch tone phone. A 6-digit security code is used to gain access, or set DIP switch 3 to the ON posi-
tion for immediate access. If a command is entered correctly, 2 beeps will be heard, 3 beeps signal an error.
Once in the remote programming mode if no commands are entered for 20 seconds, you will hear 3 beeps and the pro-
gramming mode will be terminated. If you do not want to wait 20 seconds, just enter “##7” and the programming mode
will be terminated immediately.
3
C. Using the C-250 with a Proximity Card Reader or a Separate Keyless Entry Keypad
Step 1.
Program the
ES-1
“Relay Activation Time” to match the “Doorstrike Activation Time” on the
C-250
.
Step 2.
Connect the
ES-1
relay output in parallel with the doorstrike output contacts on the
C-250
.
STAND-ALONE
DOOR CONTROLLER
ENTRY SYSTEM
VIKING
PROGRAM
PHONE
GANG
PROG
COMM
ELECTRONICS
HUDSON, WI 54016
VIKING
©
MODEL ES-1
POWER 12 VDC
BLK
RED
GRN
WHT
ENTRY POINT
WIEGAND
DEVICE
LOG
BUS
Viking PROX-1 Proximity Card Reader
(shown, not included, DOD# 221)
OR
Viking HID-2 Keypad
(not included, DOD# 199)
and/or
(Power typically not
required for gate controllers)
Doorstrike/
Magnetic Lock
5A@30VDC/
250VAC
maximum
Viking E-70 Entry Phone
(shown, not included, DOD# 207)
OR
Viking E-75 Entry Phone
(not included, DOD# 208)
LED1
S1
C
LED3 LED2
C C
1
3
2
ON
VIKING
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ENTRY CONTROLLER
WITH CALL FORWARD
POWER 13.8V AC
MODEL C-250
AUT
O ANSWER
1
EARTH GND
1
TRIGGER MODE
2
LEARN MODE
3
POWER
CALLING
LINE IN
2
3
PHONES
4
5
ENTR
Y
6
7
TRIGGER
INPUT
8
9 10 11 12
DOOR
STRIKE
N.C.
N.O.
COM
B. Using the C-250 with the CTG-1 or a Toggle Switch for Immediate Call Forwarding
Certain Hours of the Day
Note:
DIP Switch 2 must be ON.
