4
Note:
Up to 20 digits can be stored in each dial position. Special features such as one and four second pauses, and
touch tone
Q
and # count as a single digit.
The speed dial number stored in location #00 is the first outside number that will be dialed if the door phone goes off
hook and the house phone does not answer within the ring count set by location
#44
. Additional speed dial numbers
will be dialed if there is no answer or a busy at the first number. Each number is called only once. If all numbers are
called without an answer, the
C-250
will generate a CPC signal and then a busy signal will be sent to the door phone.
To clear a speed dial number position, simply enter a # and the location number (00 to 04), without any preceding num-
bers. If no numbers are programmed, the
C-250
will only call the house phone.
C. Speed Dial Numbers (Memory Locations #00 to #04)
First phone number ...........................................................................................................................
Second phone number .....................................................................................................................
Third phone number ..........................................................................................................................
Fourth phone number ........................................................................................................................
Fifth phone number ............................................................................................................................
To clear any speed dial number ...............................................................................................................
Door Strike Activation Time ...................................................................
Door Strike Command ..........................................................................
Maximum Call Time ....................................................
Maximum Ring Time .......................................................................
Ring House Phone Count .........................................................
Incoming Ring Count ............................................................................
Security Code ..................................................................................................................
To add a “
Q
“ at any point in the dialing string or door strike code ..........................................................................................
To add a “#“ at any point in the dialing string or door strike code ...........................................................................................
To disable “No CO” mode (factory setting) ............................................................................................................................
To enable “No CO” mode .......................................................................................................................................................
To disable “Doorbell” mode (factory setting) ..........................................................................................................................
To enable “Doorbell” mode ....................................................................................................................................................
To select a double burst ring pattern (factory setting) ............................................................................................................
To select a single ring pattern ................................................................................................................................................
To actuate the door strike relay ..............................................................................................................................................
To add a four second pause at any point in the dialing string ................................................................................................
To add a one second pause at any point in the dialing string ................................................................................................
Ignore touch tones for programming entry phone ..................................................................................................................
To reset all programming to factory default settings .............................................................................................................
Exit programming ..................................................................................................................................................................
The following commands are used during normal operation:
Enable Immediate Call Forward Mode .................................................................................................................................
Disable Immediate Call Forward Mode (factory setting) ........................................................................................................
(1 to 20 digits)
(1 to 20 digits)
(1 to 20 digits)
(1 to 20 digits)
(1 to 20 digits)
(no digits)
(00 to 99 sec, 00 = .5 sec, factory 5 sec)
(1 or 2 digits, blank is disable, factory 6)
(1 to 9 mins, 0 = 30 sec, blank is disable, factory 3 min)
(00 to 59 secs, 00 is disable, factory 30 sec)
(1 to 9, 0 = immediate call forwarding, factory 4)
(01 to 99, 00 disables answer, factory 10)
(6 digits, factory 845464)
B. Quick Programming Features
+
+
+
+
+
+
+
+
+
+
+
+
+
Enter Digits +
Memory
Location
#00
#01
#02
#03
#04
#00 to #04
#40
#41
#42
#43
#44
#45
#47
Q
#
Q
0
Q
1
Q
2
Q
3
Q
4
Q
5
Q
6
Q
7
Q
8
##1
###
##7
QQQ
###
Set DIP switch 3 on the front of the
C-250
to the
ON
position. Come off hook with the house phone and 2 beeps
will be heard signaling that the
C-250
is in the programming Mode. When finished programming, hang up the phone
and set DIP Switch 3 to the OFF position.
1. Local Programming
Set DIP switch 1 on the front of the
C-250
to the
ON
position. Call into the unit from a remote touch tone phone.
After the incoming ring count is up (factory set to 10), the
C-250
will answer the line and beep 1 time. Enter
Q
fol-
lowed by the 6-digit security code (factory set to 845464). Two beeps will be heard signaling that the
C-250
is in the
programming mode.
2. Remote Programming with the Security Code
Set DIP switches 1 and 3 on the front of the
C-250
to the
ON
position. Call into the unit from a remote touch tone
phone. After one ring, the
C-250
will answer the line and beep 2 times signaling that the
C-250
is in the program-
ming mode. When finished programming, hang up the phone and set DIP Switch 3 to the OFF position.
3. Remote Programming without the Security Code
