© 2010 Viking Preferred Service
13
Operation
Ice Maker and Storage Bin
Turning the Ice Maker On/Off
The On/Off switch is located on the top right-hand
side of the freezer compartment.
UÊÊÊ Ê/ÊÌÕÀÊÊÌ iÊViÊ>iÀ]ÊÃ`iÊÌ iÊ
control to the ON (left) position.
UÊÊÊ Ê/Ê>Õ>ÞÊÌÕÀÊvvÊÌ iÊViÊ>iÀ]Ê
slide the control to the OFF (right)
position.
Note:
Your ice maker has an automatic shutoff.
The ice maker sensors will automatically stop ice
production, but the control will remain in the ON
(left) position.
REMEMBER:
UÊÊ ÊÜÊÓ{Ê ÕÀÃÊÌÊ«À`ÕViÊÌ iÊwÀÃÌÊL>ÌV ÊvÊVi°Ê
Discard the first three batches of ice produced.
UÊÊÊ Ê/ iʵÕ>ÌÞÊvÊÞÕÀÊViÊÜÊLiÊÞÊ>ÃÊ}`Ê
as the quality of the water supplied to your
ice maker. Avoid connecting the ice maker
to a softened water supply. Water softener
chemicals (such as salt) can damage parts of
the ice maker and lead to poor quality ice. If a
softened water supply cannot be avoided, make
sure the water softener is operating properly
and is well maintained.
UÊÊ ÊÊÌÊÕÃiÊ>ÞÌ }ÊÃ >À«ÊÌÊLÀi>ÊÕ«ÊÌ iÊViÊ
in the storage bin. This can cause damage to
the ice container and the dispenser mechanism.
UÊÊ ÊÊÌÊÃÌÀiÊ>ÞÌ }ÊÊÌ«ÊvÊÀÊÊÌ iÊViÊ
maker or storage bin.
Removing and Replacing
Ice Storage Bin
1. Hold the base of the
storage bin with both
hands and press the
release button to lift the
storage bin up and out.
Note:
It is not necessary to
turn the ice maker control
to the OFF (right) position when removing the
storage bin. The sensor cover (“flipper door”) on
the left wall of the freezer stops the ice maker from
producing ice if the door is open or the storage bin
is removed.
2.
Replace the storage bin on the door and push
down to make sure it is securely in place.
Water Filtration System
DO NOT
use with water that is microbiologically
unsafe or of unknown quality without adequate
disinfection before or after the system.
Water Filter Status Light
The water filter status light will help you know
when to change your water filter. When the water
filter status display changes from “GOOD” to
“ORDER,” this tells you that it is almost time to
change the water filter cartridge. Replace the water
filter cartridge when the water filter status display
changes to “REPLACE.” If water flow to your
water dispenser or ice maker decreases noticeably,
change the filter sooner. The filter should be
replaced at least every 6 months depending on
your water quality and usage.
After changing the water filter, reset the status light
by pressing and holding the “FILTER” button for
three seconds. The status light will change from
REPLACE to GOOD when the system is reset.
Changing the Water Filter
1. Press the eject button to release the filter from
the base grille.
2. Pull the filter straight out.
3. Turn the cap counterclockwise to remove it
from the filter.
IMPORTANT:
Do not discard the cap. It is part
of your refrigerator. Keep the cap to use with the
replacement filter.
4. Align the ridge on the cap with the arrow on
the new filter and turn the cap until it snaps into
place.
Note:
You can run the dispenser without a filter.
Your water will not be filtered. Simply insert the cap
all of the way into the base grille and rotate the
cap until it is firmly in place.
5. Remove the covers from the O-rings. Be sure
the O-rings are still in place after the covers are
removed.
6. Push the filter into the base grille. The eject
button will pop back out when the filter is fully
engaged.
7. Flush the water system. See “Water and Ice
Dispensers.”
UNLOCKED
LOCKED