Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or
subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate
such changes.
Fax Back Doc 210
ZF301780 Rev A
Printed in the U.S.A.
P
P
r
r
o
o
d
d
u
u
c
c
t
t
S
S
u
u
p
p
p
p
o
o
r
r
t
t
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
8
8
6
6
6
6
6
6
F
F
a
a
x
x
B
B
a
a
c
c
k
k
L
L
i
i
n
n
e
e
.
.
.
.
.
.
7
7
1
1
5
5
.
.
3
3
8
8
6
6
.
.
4
4
3
3
4
4
5
5
C. Changing the Call Time-Out
The
E-10
and
E-20A
are equipped with an adjustable call time-out feature which automatically hangs-up the unit after
the pre-set time has elapsed. To change the time-out, adjust the call time pot as shown above. The time can be adjust-
ed from approximately 6 seconds to 5 minutes (factory set to approximately 3 minutes).
P
P
r
r
o
o
g
g
r
r
a
a
m
m
m
m
i
i
n
n
g
g
A. Adjusting Speaker Volume
The
SPKR VOL
pot can be adjusted to increase or decrease the speaker volume to the level desired as shown above.
B. Adjusting the Microphone Volume
In certain noisy locations (background traffic, machinery or wind), the microphone volume may need to be decreased.
A symptom of this is one-way talk path, in which the distant party cannot be heard over the speaker. A
MIC VOL
pot
is provided for increasing or decreasing the microphone volume.
Note:
If the microphone volume is set too high or too
low, one-way talk path may occur.
D. DIP Switch Programming
DIP switch 1 is for turning the Auto Answer feature ON and
OFF. The speaker phones are factory set to auto answer
when an inbound call is detected.
1 2 3
ON
DIP
Switches
OFF ON
Speaker Volume
(see section A)
-or-
E-10/E-20A E-10-EWP/E-20A-EWP
Microphone Volume
(see section B)
-or-
E-10/E-20A E-10-EWP/E-20A-EWP
Call Timer
(see section C)
-or-
E-10/E-20A E-10-EWP/E-20A-EWP
1. Auto Answer Feature ON/OFF (DIP Switch 1)
The call timer switch allows the user to turn off/disable the
call timer feature. With DIP switch 2 in the OFF position, the
call time will be unlimited and the speaker phone will not
automatically hang up until a 300ms or longer CPC break is
detected.
Warning:
If your telephone line/phone system
extension does not supply a 300ms or longer CPC break, the call timer feature must be used, DIP switch 2 ON.
2. Call Timer ON/OFF (DIP Switch 2)
With DIP switch 3 in the ON position (factory default), the VOX switching speed (delay time between talk and listen
mode) is set to FAST (0.3 seconds). In the OFF position, it is set to SLOW (0.7 seconds).
3. VOX (Talk/Listen) Switching Speed (DIP Switch 3)
Rear View of Speaker Phone models:
E-10/E-20A/E-10-EWP/E-20A-EWP
DIP
Switch
1
1
2
2
3
3
Position
ON
OFF
ON
OFF
ON
OFF
Description
Auto-Answer ON (factory default)
Auto-Answer OFF
Call Timer ON (factory default)
Call Timer OFF
VOX Speed Fast (factory default)
VOX Speed Slow
Note:
Pots are shown in factory default settings.