background image

3

2

Warnings & Important Safety Instructions ______________________________________________________________________3
Dimensions (Professional)____________________________________________________________________________________5
Dimensions (Custom Panel) __________________________________________________________________________________6
Specifications ______________________________________________________________________________________________7
Cutout Dimensions _________________________________________________________________________________________7
Drain/Electrical Locations ____________________________________________________________________________________8
General Information ________________________________________________________________________________________9
Air Flow ___________________________________________________________________________________________________9
Filters and Treatment _______________________________________________________________________________________9
Installation Overview_______________________________________________________________________________________10
Accessory Door Panel ______________________________________________________________________________________10
Custom Panel _____________________________________________________________________________________________10
Door Panel Attachment ____________________________________________________________________________________12
Door Swing Change _______________________________________________________________________________________13
Water and Drain Installation ________________________________________________________________________________14
Electrical Connection ______________________________________________________________________________________16
Final Installation ___________________________________________________________________________________________16
Installation Checklist _______________________________________________________________________________________16
Service Information ________________________________________________________________________________________17

•  Before beginning, please read these instructions completely and carefully.
•  DO NOT remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
•  Please observe all local and national codes and ordinances.
•  Please ensure that this product is properly grounded.
•                     The installer should leave these instructions with the consumer who should retain for local inspector’s use and for

future reference.

A GFI 

shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances.

• The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of

water or moisture.

• Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not

meet the requirements below.

If the use of a GFI is required

, it should be:

• Of the receptacle type (breaker type or portable type NOT recommended)
• Used with permanent wiring only (temporary or portable wiring NOT recommended)
• On a dedicated circuit (no other receptacles, switches or loads in the circuit)
• Connected to a standard breaker of appropriate size (GFI breaker of the same size NOT recommended)
• Rated for Class A (5 mA +/- 1 mA trip current) as per UL 943 standard)
• In good condition and free from any loose-fitting gaskets (if applicable in outdoor situations)
• Protected from moisture (water, steam, high humidity) as much as reasonably possible

It is your responsibility to be sure your ice machine is:
• located so the front is not blocked to restrict incoming or discharge air flow.
• properly leveled.
• located in a well ventilated area. 
• connected to the proper kind of outlet, with the correct electric supply and grounding. A 115V, 60 Hz, 15 amp fused

electrical supply is required. 

Note: Time delay fuse or circuit breaker is recommended.

• not used by anyone unable to operate it properly.
• used only for its intended purpose.
• properly maintained.

•SAVE THESE INSTRUCTIONS•

WARNING

To reduce the risk of fire, electric shock, or injury when using your unit, follow these basic precautions:

• Read all instructions before using the unit.
• Never allow children to operate, play with, or crawl inside the unit.
• Never clean unit parts with flammable fluids. The fumes can create a fire hazard or explosion.
• Always turn the power on/off switch (located behind the air grille on top right side) to the OFF

position before attempting to change light bulbs, clean, or service the unit.

FOR YOUR SAFETY

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE
VICINITY OF THIS OR ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR
EXPLOSION.

Table of Contents

Important - Please read and Follow!

Summary of Contents for FGNI515











Reviews: