background image

Technical Documentation

© 2001 VIKING

Kufstein, 3rd May 2001

Technical Information  15.01

- Page 8 -

9.

Spare parts list

A separate spare parts list is available for the MB 410 and MB 415 lawnmowers.

9.1

Standard spare parts

The standard spare parts are listed below. Optimum
performance and safety can only be ensured if origi-
nal spare parts are used. Repairs and maintenance

work may only be performed if proper procedures
are followed and all applicable safety requirements
are observed.

Quantity

Description

Part No.

1

Mowing blade

6336 702 0100

1

V-belt (MB 415)

6336 704 2100

8.

Repair times

No.

Repair procedure

MB 410/ 
MB 415

1

Complete housing replacement

45

2

Axle (front)

10

3

Axle (rear)

10/ 20

4

Wheel (front)

5

5

Wheel (rear)

5

6

Height adjustment lever (front)

10

7

Height adjustment lever (rear)

10/ 20

8

Gearbox (MB 415)

30

9

V-belt (MB 415)

10

10

Changing blade

5

11

Blade mount

10

12

Changing engine

30

13

Ejection flap 

5

14

Upper part of catcher bag

5

15

Lower part of catcher bag

5

16

Upper control arm

15

17

Lower control arm

5

18

Motorstop cable

15

19

Motorstop lever

5

20

Drive cable

10

21

Drive lever

5

22

Drive adjustment

5

The repair times indicated assume trained, qualified
staff and a perfectly equipped customer service
centre.

Repair times are given in minutes.

Summary of Contents for MB 410









Reviews: