0478 111 9932 B - EN
44
7.
1
General
●
Place the machine on level and firm
ground when performing all the
operations described.
7.2 Assembling the handlebar
Fitting the handlebar sleeves:
●
Fit protective sleeves (I) onto
handlebar (1). Position the square hole
on the inner side of the handlebar, the
bores in the handlebar and the square
hole in the handlebar sleeve must be
aligned.
Assembling the handlebar:
●
Fit handlebar (1) onto both lower
handlebar sections (2).
●
Insert flat head bolts (G) through bores
from the inside to the outside and
tighten with rotary handles (H).
1
Attaching left anti-kink cable
protection:
●
Insert all cables into anti-kink cable
protection (F).
●
First insert the anti-kink cable protection
in upper bore (3) of the lower
handlebar.
●
Then allow the anti-kink cable
protection to engage in lower slot (4) of
the lower handlebar.
2
Attaching right anti-kink cable
protection:
●
The right anti-kink cable protection (F)
is attached in the same way as on the
left side.
7.3 Installing the cable guide
●
Insert cable guide (E) into the
recesses in housing (1) and turn
towards the upper handlebar.
●
Insert all cables into the cable guide.
●
Allow the cable guide to engage in the
two bores provided using slight
pressure.
7.4 Attaching and detaching the
recoil starter rope
●
Detach the spark plug socket from the
engine before attaching and detaching
the recoil starter rope – replace
afterwards if necessary.
Attaching:
●
Press motorstop lever (1) to the
handlebar and hold.
●
Slowly pull out recoil starter rope (2)
and hold. Release the motorstop lever.
●
Attach recoil starter rope (2) in rope
guide (3).
Detaching:
●
Detach recoil starter rope (2) from rope
guide (3) and slowly return.
7.5 Installing the grass catcher
box
●
Fit upper part of grass catcher
box (C) onto lower part of grass catcher
box (B).
●
Push pin (D) through bores provided
from inside.
●
Allow the upper part of the grass
catcher box to engage in the lower part
of the grass catcher box using slight
pressure.
●
Attach the grass catcher box. (
K
Charger (MB 545 VE)
1
–
Instruction manual
1
–
Engine
instruction manual
1
7. Preparing the machine for
operation
Risk of injury!
Observe the safety instructions in
the section "For your safety" (
Item Designation
Qty.
3
Attach anti-kink cable protection (F)
only as shown. Cables must be
routed under the handlebar. Loosen
rotary handle (H) prior to assembly
if necessary.
MB 545, MB 545 T:
There are no cables on the right-
hand side of the handlebar,
therefore there is no anti-kink cable
protection on the right.
4
MB 545 VE:
The engine does not
have a recoil starter rope.
5
6
Summary of Contents for MB 545
