8
0478 121 9909 H - EN
Attaching:
Open the
M=
ejection flap and hold it
open.
The grass catcher bag is
attached by engaging the
8=
recesses in the grass
catcher bag to the
9=
mounting on the
appliance.
Close the
M=
ejection flap again
manually.
Detaching:
Open the
M=
ejection flap and hold it
open.
Lift the grass catcher bag
upwards, detach from the
9=
mounting and remove.
Close the
M=
ejection flap again
manually.
CAUTION
Risk of injury!
The motor
must
be
switched off before
attaching and detaching the
grass catcher bag.
Attaching and
detaching the grass
catcher bag
9
Notes on mowing
NOTE
To ensure a perfect, thick
lawn, mow regularly and keep
the grass short.
Do not cut too short in hot,
dry conditions as the lawn will
dry out or burn in the sun and
become unsightly.
The cutting pattern will be
better with a sharp blade than
with a blunt one. The blade
must therefore be sharpened
regularly (VIKING dealer).
CAUTION
Risk of injury!
Untangle any knots in the
cord immediately.
If using a cable drum, the
connection cord must be
unwound completely,
otherwise electrical
resistance may cause loss
of power and overheating.
Guide the connection cord
behind you when mowing.
Connection cords can be
inadvertently cut when
mowing and therefore
involve a high accident risk.
For this reason, mow so
that the connection cord is
always visible in the area of
grass that has already been
cut.
This can be read off the
H=
cutting height indicator.
Release the
I=
adjustment lever again
and allow the height
adjustment to engage.
There are
seven
cutting height
adjustment settings ranging
from
25 mm
to
80 mm
.
Level
1
= lowest
cutting height
Level
7
= highest
cutting height
The
I=
adjustment lever for the
central height adjustment
is located on the left side
of the appliance (see
illustration).
Hold the appliance at the
Y=
handle and pull the
I=
adjustment lever upwards
and hold, in order to
release the detent
mechanism.
•
Set the required cutting
height by moving the
appliance upwards or
downwards.
Central cutting height
adjustment
8
CAUTION
Risk of injury!
The motor
must
be
switched off before
adjusting the cutting height.
Ensure that you keep your
feet far enough away from
the cutting tool.
NOTE
Ensure that handlebar
adjustment is the same on
the left and right sides.
Height adjustment of
the handlebar
7
The working height of the
handlebar can be set to the
following positions
I
(low),
II
(medium) and
III
(high):
Loosen the
J=
rotary handle for
handlebar height
adjustment by turning
anti-clockwise
(approx. five turns).
Hold the
A=
upper handlebar with
both hands and bring to
the desired position by
moving up or down.
Tighten the
J=
rotary handle again by
turning clockwise.
Assembling the grass
catcher bag
6
Fit
6=
upper part of grass
catcher bag onto
7=
lower part of grass
catcher bag.
Press
8=
pins through the
apertures provided from
the inside.
Allow the grass catcher
bag upper part to
engage in the lower part
using slight pressure.
Summary of Contents for ME 545
