0478 131 9923 B - EN
114
9. Language:
Set the required display language.
The language selected during initial
installation is set as the default.
10. Contrast:
The display contrast can be
adjusted as required.
10.12 Setting the rain sensor
In order to set the 5-stage
sensor, press the control pad to
the left or right. The current
value is displayed in the "Settings" menu
by means of a line diagram.
The sensitivity of the rain sensor can be
adapted to the local conditions and
requirements. In particular, it is possible to
adjust how long the robotic mower waits
for the mowing area to dry following rain.
In the case of
medium
sensitivity
, the robotic
mower is ready for operation
under normal ambient
conditions.
Move the bar further
to the
left
for mowing at a higher
humidity. If the bar is moved
all the way to the left, the
robotic mower will mow even
in wet external conditions and will not
interrupt the mowing operation if rain drops
land on the sensor.
Move the bar further
to the
right
for mowing at a lower
humidity. If the bar is moved
all the way to the right, the
robotic mower will only mow if
the rain sensor is completely dry.
10.13 Setting the status screen
In order to configure the status screen,
select the left or right screen with the
control pad and confirm with OK.
Charge state
:
Shows the battery symbol with the
charge state in percent
Rem. time
:
The remaining mowing duration
during the current week in hours and
minutes
Time and date
:
Current date and current time
Start time
:
Start of the next planned mowing
operation. During a running active
time, the text "active" is displayed.
Mowing ops
:
Total number of mowing operations
performed
Mowing hours
:
Total duration of all mowing
operations performed
Distance
:
Total distance covered
10.14 Installation
1. Corridor:
Switching offset drive home on and off.
When the corridor is activated, the robotic
mower travels back home to the docking
station, offset at a distance, along the
perimeter wire.
Corridor width:
30-70 cm
The distance to the perimeter wire within
the corridor is selected randomly.
2. New installation:
The installation assistant is started
again, the existing mowing plan is
deleted. (
3. Starting points:
The robotic mower either starts the
mowing at the docking station
(default setting) or at a starting point.
Starting points are to be defined
– if partial areas are to be travelled to in a
targeted manner because they are
insufficiently mowed,
– if areas can only be accessed via a
corridor. At least one starting point must
be defined in these partial areas.
●
Setting starting points (
4. Edge testing:
Start the test run for checking
correct wire routing.
The step "Check installation" of the
installation assistant is called up. (
In conjunction with an external
docking station, a separately
available accessory is required for
offset drive home (AED 600). More
information can be obtained from
your VIKING dealer.
Offset drive home can only be
activated when the perimeter wire
has been routed with a clearance of
at least 2 m at the narrowest
sections. No corridors may be
installed within the mowing area.
To check correct wire routing
around no-go areas, position the
robotic mower in the mowing area
with the front facing the no-go area
and start a test run.
Summary of Contents for MI 422
