12
Villager
VLN 1140 / VLN 1155
(GB)
Adjusting the angle of the shoe
The shoe can be tilted to angles between 0° - 45° left or right so that you can cut
bevel angles in a work piece.
1.
Before performing any adjustments ensure the tool has been switched off and
is disconnected from any power supply.
2.
Turn the Jigsaw upside down and use the hex key to loosen the shoe locking
screws that secure the shoe.
3.
Side the shoe backwards away from the blade.
4.
Tilt the shoe between 0° and 45° left or right, Fig.B
Note:
Bevel angles of 0°, 15°, 30° and 45°are marked on the bevel scale.
5.
Once the angle has been set, slide the shoe forwards again and tighten the shoe
locking screws.
If an accurate bevel is required, it is best to check the setting with a protractor
or by making a trial cut in a piece of scrap material and re-adjusting the setting
if necessary.
Operation
1.
The shoe should always be kept flat against the work piece when performing a
cut.
2.
Take care to always select the correct blade for the job at hand.
Cutting on a straight or curved line
Note:
A range of blades are available from your local Villager store.
1.
Mark your cutting line with a pencil or other suitable marker.
2.
Start the tool by squeezing the on/off switch trigger and wait a few seconds
until the blade achieves maximum speed, Fig.C.
3.
Place the shoe on the work piece and move forward slowly along the cutting
line. Take extra care and time when cutting curved lines in order to reduce
stress on the blade and chance of breaking it.
Let the tool work at its own pace. Do not overload the tool by pushing hard into
the cut.
4.
For sustained cutting you can press the lock-on switch to keep the trigger switch
engaged, Fig.D. To release the lock on switch press the trigger switch then
release it.
Summary of Contents for VLN 1140
