6
RS16.P
EN
Trimmer Description
MOT 1
Power of motor (turn the trimmer clockwise to increase the power)
7 Functions of the buttons
Button
Description
PRG
Button for programming the travel
MRX
Button for programming or deleting remote controls
51
Step-by-step command button
5.2 Reversing the opening direction
1. While the gate is stationary and not closed, press and hold PRG for 2 s; the flashing light comes on and remains steadily lit to indicate that program
-
ming is in progress. The gate closes.
2. Press MRX (the gate stops).
3. Create a pulse (e.g. Press 51); the gate begins to close.
5.3 Changing the pedestrian opening position
1. Have a remote control available with the 2nd radio channel stored.
2. While the gate is closed, press and hold PRG for 2 s; the flashing light comes on and remains steadily lit to indicate that programming is in progress.
The gate opens.
3. Once the desired opening position has been reached, press the button on the remote control stored as the 2nd radio channel.
Note:
If you want to return the control panel to default, perform the following procedure:
1. Disconnect the power to the control panel.
2. Press and hold the PRG button.
3. Reconnect the power to the control panel and wait for the flashing light to come on steady.
4. After 3 sec., release the PRG button. The flashing light will turn off.
5. The control panel is now set with the default times.
6 Trimmer functions
O
1
-
+
PHC PHO STP
MRX
PWR
51
63 61 99
O
1
-
+
PHC PHO STP
MRX
PWR
51
63 61 99
-
+
TP
9
ON
1 2 3 4 5 6 7 8
+
MRX
PWR
51
PRG
MRX
AN
AN
ON
1 2 3 4 5 6 7 8
+
MRX
PWR
51
PRG
MRX
AN
AN
ON
1 2 3 4 5 6 7
+
PWR
51
PRG
MRX
8 DIP-switch functions
ON
1 2 3 4 5 6 7 8
PWR
51
ANT _
ANT _
ON
1 2 3 4 5 6 7 8
PWR
51
ANT _
ANT _
ON
1 2 3 4 5 6 7 8
A
Dip
Function
Status Description
DIP 1
Close immediately OFF
Close immediately off
ON
Close immediately on:
The engagement and subsequent disengagement of the photocell when
closing, while opening or during the pause time causes the gate to re-
close immediately at least 3 s after full opening, regardless of the set
automatic closing time
DIP 2
Automatic closing
OFF
Automatic closing off
ON
Automatic closing on
DIP 3
Step-step logic
OFF
2 steps: step-by-step (term. 51 and radio) with logic in 2 steps (open -
close - open)
ON
Step-by-step command (term. 51 and radio) with logic in 4 steps (open -
stop - close - stop - open - stop)
DIP 4
Apartment block
OFF
Apartment block off
ON
Apartment block on (while the gate is opening, you cannot stop the
movement with a radio command or with inputs 51 (step-by-step) and
52 (pedestrian). With automatic closing on (DIP-switch 2 = ON) and the
gate open, an additional step-by-step command (terminal 51 or radio
command) renews the pause time and if input 51 remains engaged the
control panel suspends the pause count until the input is disengaged (for
connecting any coils or a timer)
DIP 5
Slowdown distance OFF
Slowdown distance at 10% of the travel
ON
Slowdown distance at 20% of the travel
DIP 6
Input 63 function
OFF
Input 63 configured as photocell (PH)
ON
Input 63 configured as safety edge (BAR)
DIP 7
Action speed
OFF
Action speed high
ON
Action speed low
DIP 8
Photo-test
OFF
Photo-test off
ON
Photo-test on
At the start of each action, the control panel checks the operation of the
photocells. It requires specific wiring
