background image

                                                       

 

                       

 

- 17 - 

 

 

Fig. 5 WM-250~450SCUR Condensing Unit 

 

                                        

 

         

  Fig. 6 WM-Liquid Filter          Fig. 7 WM-Liquid Indicator         

 

2.  Temperature Controller and Air Probe Location 
 

1)  The temperature controller can be mounted either inside or outside the wine 

cellar, but the air probe must be located inside. 

2)  The air probe shall be located in the wine cellar 5 ft above the floor or the air 

return  area,  but  it  shall  not  be  located  in  the  air  supply  area  or  other  areas 
where air is not circulated. 

3)  Air  probe  can  be  pulled  out  of  the  temperature  controller  up  to  5  ft.  If 

additional wires are necessary, 18 gauge wires may be used to extend the air 
probe. 

 

3.  Evaporator Unit Location 

 

1)  The  WM-25~45SFCO  evaporator  units  shall  be  installed  above  the  ceiling 

with the supply air at one side and return air at the other side. It shall not be 
exposed to temperatures higher than 85 °F. Make a cutout L1 x W1. 

Summary of Contents for WINE-MATE WM-2500SSO






























Reviews: